Quick Answer: This 25 ohm variable resistor is an adjustable resistor whose resistance can be set anywhere from near zero to 25 ohms. In its usual rheostat form a sliding contact moves along a coil of resistance wire, and the resistor is used to control current in a circuit or, with all three terminals connected, as a potential divider.
Two Ways to Connect a Variable Resistor
Used with two terminals, one end of the coil and the sliding contact, the variable resistor sits in series with the circuit and acts as a rheostat. Moving the slider changes the length of wire the current passes through, and with it the resistance, from almost nothing to the full 25 ohms. This is the standard way to change the current in Ohm’s law, lamp and electrolysis experiments and to take a set of readings without changing the supply.
Used with all three terminals, the coil is connected across the supply and the output is taken between one end and the slider. The device then works as a potential divider, giving any voltage from zero up to the full supply. This arrangement reaches lower voltages than the series connection, which can never reduce the current to zero, so it is preferred for current-voltage characteristics that must start at the origin, such as those of filament lamps and diodes.
The total value matters. A 25 ohm rheostat gives useful control when the rest of the circuit has a resistance of a similar order, from a few ohms to a few tens of ohms, as with lamps, low-value resistors and coils. In a circuit of several hundred ohms, 25 ohms would change the current only slightly, and a rheostat or resistance box of higher value is the better tool. Other wire-wound designs, such as the constantan (Eureka) wire rheostat, are listed alongside it.
Care & Handling
- Set the 25 ohm variable resistor to its maximum value before switching on, then reduce it gradually, so the circuit starts with the smallest current.
- Keep within the current rating; at low settings the whole current passes through a short length of wire, which heats quickly.
- Keep the sliding contact and the wire clean, so the contact stays steady and does not jump.
- Do not rest books or other apparatus on the coil, and keep it away from the edge of the bench where it can be knocked.
Applications
- Varying the current in Ohm’s law experiments to obtain a set of readings
- Setting voltages from zero upward as a potential divider for I–V characteristics
- Dimming a lamp to show how brightness and filament resistance change with current
- Controlling the current through a coil or solenoid in magnetism experiments
- Holding a steady current in electrolysis and heating experiments as conditions change
Specifications
| Component | Variable resistor (rheostat) |
| Maximum resistance | 25 ohms, as titled |
| Connections | Two terminals as a rheostat; three as a potential divider |
| Typical use | Current and voltage control in low-voltage circuits |
| Current rating and construction | Confirm at enquiry |
Why Choose LabEquip
Schools and colleges keep variable resistors at every electricity station, because almost every practical needs current control. A 25 ohm value suits circuits with lamps such as the 3V bulb and with low-value resistors; LabEquip’s physics lab equipment also covers higher-value rheostats. Use the contact page to ask about current ratings and quantities.
Frequently Asked Questions
What is the difference between a rheostat and a potential divider connection?
As a rheostat, two terminals are used and the resistor controls current in series with the load. As a potential divider, all three terminals are used, the full coil sits across the supply, and the slider picks off any voltage from zero to the supply voltage.
Why start with the slider at maximum resistance?
Starting at maximum gives the smallest current when the circuit is first switched on. That protects meters and lamps from a sudden surge and gives a safe starting point for the readings.
Can a 25 ohm rheostat reduce the current to zero?
Not on its own in series, because some current still flows at maximum resistance. To reach zero, connect it as a potential divider, where the output voltage, and so the current in the load, can be set right down to zero.
Why does the rheostat get warm?
Current passing through the resistance wire produces heat at a rate of I²R. At low settings the whole current flows through a short length of wire, so that part heats fastest. Stay within the rating and switch off between readings.
When is a 25 ohm value too small?
When the rest of the circuit has a resistance of hundreds of ohms or more. Adding or removing 25 ohms then changes the current only slightly, so choose a higher-value rheostat or a resistance box for such circuits.
How should the sliding contact be cared for?
Keep the wire and the slider’s contact clean and dust-free, and move the slider smoothly rather than flicking it. A dirty contact makes the current jump and can cause small sparks that pit the wire.
Last Updated: October 2026










Reviews
There are no reviews yet.