Quick Answer: The Thermostatic Bath Corio is an open heating bath from the Corio range: a heating circulator (a control head with heater, sensor and pump) mounted at one end of a stainless steel tank, which heats and circulates the bath liquid so immersed vessels are held at a steady set temperature.
How a Corio Thermostatic Bath Differs from a Simple Water Bath
A basic water bath heats from below and relies on convection, so water near the element runs warmer than the far corners. A Corio thermostatic bath uses a circulator instead: a control head whose heater, temperature sensor and pump hang into the liquid. The pump keeps the whole tank moving, so the reading at the sensor is much closer to what every sample experiences.
In the listing photo the control head is clamped at one end of a long, shallow open tank, leaving the rest of the surface free for flasks, bottles or racks. The model letters that identify the exact Corio variant are not part of the title, so heater power, pump output and temperature range are not stated on this page.
Circulators of this type often have pump connections that can also feed an external loop, such as a jacketed vessel. Whether this unit is set up for external circulation, and which tubing it takes, should be settled with the model number in hand.
Specifications
| Type | Open heating bath with mounted heating circulator |
| Range name | Corio, as titled |
| Tank | Long, open stainless steel tank, as pictured |
| Circulation | Pump in the circulator head stirs the bath liquid |
| Bath liquid | Usually water; other fluids only within the unit’s rating |
| Model variant, range and output | Confirm at enquiry |
Care & Handling
- Fill the Corio thermostatic bath to the level marked on the tank before switching on; running the heater with too little liquid can trip its protection.
- Use clean, softened or distilled water and change it regularly; add a bath protectant if algae appear.
- Never use a flammable bath fluid unless the circulator is specified for it, and stay below the fluid’s safe working temperature.
- Keep splashes off the control head and wipe it dry after filling or emptying.
Applications
- Holding samples at a fixed temperature for viscosity, density or similar measurements
- Conditioning sample bottles and reagents before testing
- Long incubations where a uniform temperature across the whole tank matters
- Supplying temperature-controlled liquid to a jacketed vessel, where the model allows external circulation
Why Choose LabEquip
Quality-control and research labs choose a stirred thermostatic bath when tests demand the same temperature in every position of the tank. LabEquip lists other Corio variants such as the Thermostatic bath CORIO C-B in General Lab Products, and can help pick the right model through the contact page.
Frequently Asked Questions
What is the difference between a thermostatic bath and an ordinary water bath?
A thermostatic bath stirs its liquid with a pump and controls it with a sensor in the moving stream, so the tank stays more uniform. An ordinary unstirred water bath heats by convection alone and shows larger differences between positions.
Can bath fluids other than water be used?
Circulators are often run with water-glycol mixtures or thermal oils, but only within the limits set for the specific unit. Check the fluid’s flash point and the circulator’s rating before changing from water.
Can the bath supply heat to an external vessel?
Many circulators have pump outlets for that purpose, so a jacketed reactor or a viscometer cell can be held at temperature. Make sure the Corio model you order has external pump connections before planning such a set-up.
Why is the circulator mounted at one end of the tank?
Placing the head at one end leaves the rest of the open surface free for vessels, while the pump drives liquid along the tank. The working area stays uncluttered and easy to reach.
How do I reduce evaporation?
Use a bath cover when the work allows, and top up with liquid at a similar temperature. At higher set points evaporation is fast, so check the level before leaving a run unattended.
What maintenance does the circulator need?
Descale the heater and pump area periodically, change the bath liquid when it discolours and keep the sensor clean. Follow the instrument manual for any internal servicing.
Last Updated: October 2026










Reviews
There are no reviews yet.