Quick Answer: The Refrigeration System CDP115 is an add-on cooling unit for laboratory water baths, pictured as a compact stainless steel housing with a cooling fan on a mounting bracket, used to remove heat so that a suitable bath can hold temperatures close to or below room temperature.
Why a Water Bath Needs Cooling
A standard water bath can only heat. Its lowest steady setting sits a few degrees above room temperature, because the controller needs a margin to regulate against, and on a warm day or in a crowded room that floor rises further. Work at 20 °C or 25 °C, common for enzyme kinetics, stability samples and some quality control tests, then becomes unreliable. An add-on cooler removes heat continuously while the bath’s heater trims the temperature, so the bath can hold settings near or below ambient.
The photo shows a compact stainless housing with a fan grille, a switch on the side and a bracket fixed to a support rail, the arrangement used by units that mount at the edge of a bath. The title gives the model code CDP115 but not the bath series it fits or how it cools; compact fan-cooled units of this kind often use thermoelectric (Peltier) modules, while larger coolers use a compressor.
The cooler works with the bath rather than replacing its controller. The bath’s heater and controller still regulate; the cooler provides a steady pull of heat for the heater to balance against. A lid on the bath reduces the load, as does starting from water already close to the target.
When a Cooled Bath Is Needed
- Holding samples at 20 °C or 25 °C in warm rooms for enzyme and kinetics work
- Stability studies and conditioning of samples just below ambient temperature
- Measurements such as viscosity or density that need a fixed temperature near room temperature
- Bringing a bath down quickly between a warm step and a cooler one
Specifications
| Type | Add-on cooling unit for laboratory water baths |
| Model | CDP115, as titled |
| Housing | Compact stainless steel with cooling fan, as pictured |
| Mounting | Bracket for fixing at the bath, as pictured |
| Role | Removes heat so the bath can hold settings near or below room temperature |
| Compatible baths and cooling method | Confirm at enquiry |
Care & Handling
- Leave clear space around the fan so warm air can escape; a blocked fan cuts cooling and can overheat the unit.
- Mount the unit only on a bath it is made for, and route the power cable well away from water.
- Dust the fan grille regularly and keep the housing dry when filling or emptying the bath.
- Use a bath lid during cooled operation to reduce heat gained from the room.
Why Choose LabEquip
Pharmaceutical QC labs, food testing labs and research groups that already own a water bath buy the CDP115 to take it below ambient without replacing the bath. LabEquip lists it in General Lab Products; send your bath model through the contact page so the fit can be checked before you order.
Frequently Asked Questions
Why can a water bath not hold room temperature on its own?
A heated bath can only add heat. It needs to sit a few degrees above ambient to regulate, and heat from the room and the bath’s own electronics pushes the water up further. A cooling unit gives the controller something to balance against.
Does the CDP115 replace the bath’s controller?
No. The bath’s heater and controller still set and hold the temperature. The cooling unit removes heat steadily in the background.
Is it a Peltier or a compressor cooler?
The title does not say. Its compact, fan-cooled housing is typical of thermoelectric units, but the cooling method and capacity should be confirmed at enquiry together with the bath it fits.
Will the bath cool faster with the lid on?
Yes. A lid cuts heat gained from the room and reduces evaporation, which otherwise cools the surface unevenly. Both make the set temperature easier to hold.
Where should the unit be placed?
On the bath it is designed for, with free air around the fan and the cable clear of water. Avoid spots next to ovens or other heat sources that warm the air it relies on.
Can the bath be used without the cooler fitted?
Yes. The bath works as a normal heated water bath; the cooler is only needed for settings close to or below room temperature.
Last Updated: October 2026










Reviews
There are no reviews yet.