Search

In Stock

Melde vibrator cord

Cordelette pour vibreur de Melde, High-Contrast Braided Surface Enables precise visual Analysis and identification of nodes and antinodes during stationary wave formation in varied lighting environments.

Low-Hysteresis Synthetic Fibers support the Evaluation of frequency response and tension variables without material-induced data drift, ensuring evidentiary-grade laboratory results.

$4.12

Quick Answer: The Melde vibrator cord is the string used in Melde’s experiment. One end is fixed to a vibrator and the other runs over a pulley to a hanging load, so the cord can be set into standing waves and the loops counted to study the laws of vibrating strings.

The Cord’s Role in Melde’s Experiment

Franz Melde’s arrangement drives a stretched cord from one end with a vibrator, originally a tuning fork and now often an electrically driven vibrator. At particular combinations of tension, length and frequency, waves travelling along the cord and waves reflected from the far end combine into a steady pattern of loops. The nodes barely move and the antinodes swing widely.

The cord sets the conditions for that pattern. Its mass per unit length, written μ, together with the tension T, fixes the wave speed v = √(T/μ). With a vibrating length L carrying n loops, the frequency is f = (n/2L)√(T/μ). A cord with an even linear density along its whole length gives evenly spaced loops and repeatable readings; a frayed, knotted or overstretched section distorts the pattern.

LabEquip also lists a rope for Melde’s vibrator as a separate item. Neither listing states a material or linear density, so check which one matches your vibrator and pulley before ordering; this page describes the cord used for standing-wave measurements.

Specifications

Item Cord for Melde’s standing-wave experiment
Used with Melde vibrator or tuning fork, pulley and slotted mass hanger
Key property Uniform mass per unit length along the cord
Relation used f = (n/2L)√(T/μ)
Material, length and linear density Confirm at enquiry

Applications

  • Finding the frequency of the vibrator from the loop count, the tension and the measured linear density
  • Verifying that the number of loops varies inversely with the square root of the tension
  • Comparing transverse and longitudinal arrangements of the vibrator
  • Demonstrating nodes, antinodes and resonance in wave lessons

Care of the Cord

  • Measure the linear density before the practical by weighing a known length of the same cord, since this value enters every calculation.
  • Do not overload the hanger; excess tension stretches the cord and permanently changes its linear density.
  • Keep the cord free of knots except at the attachment points, and replace it once it frays.
  • Coil it loosely for storage, away from heat and sunlight.

Why Choose LabEquip

Physics departments running Melde’s experiment keep spare cords, because a stretched or frayed cord is a common cause of irregular loops. This cord is listed in General Lab Products, and the membrane Melde’s vibrator in the physics range is a driving unit it can be paired with.

Frequently Asked Questions

How do I measure the linear density of the cord?

Mark a known length, weigh it on a sensitive balance and divide the mass by the length. Work in kilograms and metres so the result is in kg/m and can go straight into the wave-speed formula.

Why do I see no clear loops even with the vibrator running?

The tension, length and frequency do not yet match a standing-wave condition. Change the hanging mass in small steps, or move the pulley to alter the vibrating length, until the cord settles into steady, well-defined loops.

What is the difference between the transverse and longitudinal arrangements?

In the transverse arrangement the vibrator moves at right angles to the cord, which vibrates at the vibrator frequency. In the longitudinal arrangement it moves along the cord, which then vibrates at half that frequency, so the loop count changes.

How does the number of loops change with tension?

For a fixed length and frequency, the number of loops is inversely proportional to the square root of the tension. Quadrupling the hanging load halves the number of loops, which students can check directly.

Does the weight of the scale pan count in the tension?

Yes. The tension equals the total hanging mass, including the pan or hanger, multiplied by the acceleration due to gravity. Leaving the pan out is a common source of error in Melde calculations.

Can the same cord be used with a tuning fork?

Yes, provided the fork is mounted so it can drive the cord and is kept sounding, for example by electrical maintenance. A light cord responds more readily than a heavy one, because a fork delivers only a small amount of energy.

Last Updated: September 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)