Quick Answer: The Brush, Test Tube is a twisted-wire test tube brush with a head of bristles on a long wire stem, used to scrub the inside of test tubes and boiling tubes clean after practicals, right down to the rounded bottom that a cloth or swirl of water cannot reach.
How a Twisted-Wire Brush Cleans a Tube
Brushes of this kind are made by twisting a doubled length of wire around a row of bristles, which locks them in place and fans them out into a cylindrical head. The bare wire carries on as the handle, sometimes finished with a loop for hanging. Many patterns add a small tuft at the tip, so the curved base of the tube is swept as well as the walls; that base is where precipitates and dried residues usually collect.
The head should be slightly wider than the bore of the tube, so the bristles press against the glass. Pushed in with a twisting motion and drawn back out, the brush scours the whole inner surface in a few strokes, loosening films of precipitate, dried indicator, grease from organic tests and the brown stain that strong heating leaves behind. Work over the sink with warm water and a laboratory detergent: the bristles do the mechanical work while the detergent lifts oily material.
This brush is sized for standard test tubes and boiling tubes. For narrower culture tubes, sample vials and small-necked bottles, the Brush, Tubes/Vials is the companion item, intended for openings where a test tube brush would jam.
Where the Brush Is Used
- Washing tubes after qualitative salt analysis, where coloured precipitates cling to the glass.
- Removing residues from boiling tubes used for heating solids or evaporating solutions.
- Cleaning tubes after food tests such as the Benedict’s and biuret tests, ready for the next class.
- Removing visible residue before tubes are sterilised for microbiology work.
Specifications
| Type | Twisted-wire tube brush |
| Head | Bristles held in a twisted wire core; many patterns have a tip tuft |
| Intended for | Test tubes and boiling tubes |
| Handle | Continuation of the wire stem |
| Bristle material and head diameter | Confirm at enquiry |
Care & Handling
- Let the tip lead gently into the tube; jabbing the bare wire end against the base can crack thin glass or score plastic.
- Rinse the brush after use and hang it head-down or lay it flat, so water does not sit in the twisted core and rust the wire.
- Keep separate brushes for glassware used with biological material and for chemical glassware.
- Retire a brush once the bristles are worn down towards the wire.
Why Choose LabEquip
School and college chemistry and biology departments buy the test tube brush by the dozen, usually several per wash-up sink, and replace them every few terms as the bristles wear. LabEquip lists them in General Lab Products alongside drying items such as the wooden test tube stand with drying pegs, and larger orders can be discussed through the contact page.
Frequently Asked Questions
How do I choose the right size of brush for my tubes?
Pick a head slightly wider than the inside of the tube, so the bristles are compressed a little and press on the glass. A head much wider than the bore jams and bends the wire, while one that is too narrow spins without scrubbing the walls.
Can a brush scratch glassware?
The bristles are softer than glass and do little harm, but the bare wire can scratch when the bristles are worn short or when the tip is pushed hard against the base. Scratched glass is weaker and more likely to crack when heated, so worn brushes should be retired.
What removes stains that brushing leaves behind?
Soak the tube in warm detergent solution first, then brush again. Residues that still remain, such as some metal oxides or charred organic matter, may need a dilute acid rinse prepared and used under a teacher’s or technician’s supervision, followed by thorough rinsing with water.
Can the same brush be used on plastic test tubes?
Yes, if the bristles are soft and the brush is used gently. Plastic scratches more easily than glass, and scratches trap residue, so avoid scouring powders and do not force the wire tip against the bottom of the tube.
How is this brush different from the tubes and vials brush?
It is sized for ordinary test tubes and boiling tubes. The tubes and vials brush is intended for narrower openings such as sample vials and culture tubes, where a head this wide would not fit.
How should brushes be stored between practicals?
Hang them head-down from a hook near the sink, or stand them handle-down in a dry beaker, so they drain and dry in the air. Brushes left wet in a closed drawer can go mouldy and rust at the wire core.
Last Updated: September 2026










Reviews
There are no reviews yet.