Search

In Stock

Socket, Single, Interchangeable

Standardized 1:10 Taper Profile: Each socket is precision-ground to international metrological specifications, featuring a high-vacuum matte finish that ensures leak-proof hermetic sealing with any compatible male cone interface.

Annealed Borosilicate 3.3 Composition: Constructed from low-expansion glass, these sockets undergo controlled thermal processing to eliminate residual internal strain, ensuring structural integrity during high-temperature reflux and rapid thermal cycling.

$3.50

Quick Answer: A single interchangeable socket is the female half of a standard ground-glass joint: a tapered glass sleeve ground on its inside, usually attached to a plain tube. Glassblowers fuse it onto flasks, tubes and custom vessels so they accept any standard cone of the same size.

The Female Half of a Joint

A socket is ground on the inside and a cone on the outside, and the two meet along the same standard taper. Sold singly, the socket is a raw component: the plain tube beyond the ground zone is left long so that a glassblower can cut it to length and join it to the neck of a flask, the top of a condenser, the end of a column or a purpose-made vessel. Fitting a new socket to a damaged piece is often simpler than replacing a whole condenser or multi-neck flask.

The socket supplied here is a standard interchangeable socket. Its size is not stated, and it should be matched to the cones it will receive, because a socket seals only against a cone of the same nominal size. The male partner is listed as a single interchangeable cone.

In use, sockets are more vulnerable than cones, because the thin rim at the wide end chips when a cone is pushed in off-centre. A chipped rim does not always leak, but it sheds glass fragments into the apparatus and weakens the joint, which is a common reason for fitting a new socket.

Care & Handling

  • Store sockets with the rim protected, in a tube or wrapped in paper, as the thin wide end chips easily.
  • After fusing, anneal the joint area to remove strain before the apparatus goes into service.
  • Test the finished socket against a known good cone carrying a light film of grease; the ground zone should turn evenly clear with no streaks.

Applications

  • Rebuilding a broken socket on a flask neck, condenser or still head
  • Building one-off reaction vessels and gas manifolds that need a female joint
  • Adding a jointed opening to apparatus that previously took a rubber bung
  • Glassblowing training in scientific glass technology courses

Specifications

Item Single ground-glass socket (female joint)
Ground surface Inside, standard taper
Shank Plain tube for fusing; length not stated
Mates with A cone of the same nominal size

Why Choose LabEquip

Glassblowing workshops and large institutional labs keep loose sockets in their common sizes so broken apparatus can be restored in-house. LabEquip supplies them within its chemistry lab equipment range; state the size and quantity on the contact page.

Related Products

Frequently Asked Questions

What is the difference between a ground-glass socket and a cone?

A socket is the female half of the joint, ground on the inside; a cone is the male half, ground on the outside. The two meet along the same standard taper and seal against each other. The single interchangeable socket is the female half, supplied on its own.

Can a single socket be used without glassblowing?

Not by itself. The single socket comes with a plain glass tube beyond the ground zone, left long so a glassblower can cut it and fuse it onto a flask neck, condenser, column or custom vessel. It is a component for building or repairing apparatus.

How do I choose the right socket size?

Match the socket to the cones it will receive. Joint sizes are given as two numbers, such as 19/26 or 24/29: the first is the approximate diameter at the wide end of the ground zone and the second its length. A socket seals only against a cone of the same size.

Why does a newly fused socket need annealing?

Fusing glass leaves stress where the hot and cold parts met. Annealing, heating the finished piece evenly and cooling it slowly, relieves that stress, so the joint does not crack later when heated or under vacuum.

Can a slightly chipped socket still be used?

A chip on the ground sealing surface lets gas or vacuum leak and can spread into a crack, so the socket should be repaired or replaced. A small chip on the outer rim, away from the ground zone, is less serious but should be watched.

Do sockets from different makers fit the same cones?

Interchangeable joints are made to a standard taper, so a socket and cone of the same nominal size fit regardless of maker. That is what allows a broken socket on one item to be replaced with a single socket of matching size.

Last Updated: November 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)