Quick Answer: The Hofmann electric burner regulator is a plug-in power control box. The listing photo shows a white unit with a mains socket on its face, a rotary dial with a printed scale and a cable with a plug, so the burner plugs into the regulator and its heat is set with the dial.
Turning a Fixed Burner into an Adjustable One
An electric burner without a control runs flat out whenever it is switched on. That suits sterilising a loop, but not warming a solution slowly or keeping a liquid just below the boil. An electric burner regulator sits between the wall socket and the burner and reduces the power reaching the heating core, which lowers its heat output.
The unit in the photo follows a common plug-in pattern. Its own cable goes to the wall socket, the burner’s plug fits the socket on the front of the regulator, and the dial beneath sets the level. Nothing has to be wired in, and the regulator can sit on the bench a safe distance from the heat.
The regulator is listed for the Hofmann electric burner, and a power controller should only be used with a heater it is rated for. Some burners in this range appear from their photos to have heat control built in, such as the knob on the LAB 2 electric Bunsen burner, and would not need a separate regulator.
Specifications
| Item | Plug-in power regulator for the Hofmann electric burner |
| Connections | Mains cable with plug; socket on the front for the burner (photo) |
| Control | Rotary dial with a printed scale (photo) |
| Function | Varies the power, and so the heat, delivered to the burner |
Applications
- Evaporating a solution gently, without spitting, before crystallisation
- Holding a small beaker of water near a steady temperature for a heating-curve activity
- Keeping heat low for younger classes, then raising it for a teacher demonstration
- Warming heat-sensitive samples more slowly than full power would allow
Care & Handling
- Use the regulator only with the Hofmann burner or another heater within its stated rating; never connect kettles, hot plates or other appliances.
- Keep the regulator on the bench away from the burner’s heat and from any liquid.
- Turn the dial to its lowest setting before plugging in the burner, then raise it gradually.
- Unplug both units at the end of the session and include them in routine portable-appliance inspections.
Why Choose LabEquip
Teachers who already use the Hofmann burner and need finer control for evaporations or slow heating are the usual buyers of this regulator. It is listed in LabEquip’s chemistry lab equipment; tell us your country of use through the contact page so the plug and socket match your mains outlets.
Related Products
- Hofmann Electric Burner: The Hofmann electric burner that plugs into this regulator for adjustable heat.
- Hofmann Electric Burner Guard: The perforated guard for the Hofmann burner, on whose prongs a vessel sits while the heat is set low.
- Electric Beak Dimmer: The Electric Beak Dimmer, a timed regulator for the Microbio and Technibec electric burners.
- Electric Bunsen Burner LAB 2: The LAB 2 electric burner, which has its own graduated control knob on the front.
Frequently Asked Questions
How does the regulator change the Hofmann burner’s heat?
The regulator sits between the wall socket and the burner and reduces the power reaching the heating core. Turning the dial, shown with a printed scale in the listing photo, lowers or raises the heat output, so the burner can warm gently instead of running flat out.
Can the Hofmann burner regulator be used with other heaters?
It is listed for the Hofmann electric burner, and a power controller should only be used with a heater it is rated for. Using it with a hot plate or another appliance of different power can overload it or give unpredictable control.
Why use a regulator instead of switching the burner on and off?
Switching on and off gives only full heat or none, so temperatures swing up and down. A regulator gives a steady, lower output, which is what slow warming, keeping a liquid just below the boil or drying a sample gently needs.
Does an electric burner regulator get warm?
Some warmth is normal while it is controlling power. Keep it on a clear part of the bench with its vents uncovered, and stop using it if it becomes hot to the touch, smells of burning or the dial no longer changes the heat.
Where should the regulator sit during a practical?
Place it on the bench a safe distance from the burner, where hot vessels, spills and the burner’s heat cannot reach it, and where the dial is easy to reach. Route the cables so they cannot be caught by elbows or pulled off the bench.
How is this regulator different from the Electric Beak Dimmer?
This regulator is listed for the Hofmann electric burner and plugs between it and the mains. The Electric Beak Dimmer is a timed regulator whose panel names the Microbio and Technibec burners. Each control is matched to the burners it is listed for.
Last Updated: November 2026










Reviews
There are no reviews yet.