Search

In Stock

Belts and Pulleys Test Bench

Banc d’essai courroies poulies, Interchangeable Multi-Diameter Pulleys Enables the technical Evaluation of angular velocity ratios and torque transformation, supporting the Advanced Kinematics Module 402.

Integrated Slip Quantification Interface supports the Application of mechanical drive theories in real-world scenarios, allowing students to calculate losses in non-synchronous belt systems.

Ruggedized Bearing Support Blocks ensure laboratory Consistency across multi-year curriculum cycles by minimizing parasitic vibration and shaft deflection.

₹2,456.00

Quick Answer: A belts and pulleys test bench is a mechanical teaching bench on which a belt carries rotation from a driving pulley to a driven pulley. Students use the belts and pulleys test bench to measure speed ratios, see how an open or crossed belt sets the direction of rotation, and observe the effects of belt tension and slip.

Speed Ratio From Pulley Diameters

If the belt does not slip, every point on it moves at the same speed, so the rim speeds of the two pulleys are equal: πD₁n₁ = πD₂n₂. The speed ratio is therefore n₂/n₁ = D₁/D₂. A small driving pulley turning a pulley three times its diameter makes the output turn at one third of the input speed. Students can check this by marking both pulleys, turning the input ten times and counting the output turns.

In an ideal drive the power passed on stays the same, so if the speed drops to one third the torque available at the output rises about threefold. This trade between speed and turning force is the reason belt drives are used to slow motors down to useful working speeds.

Open Belts, Crossed Belts and Slip

An open belt runs straight between the pulleys and both turn the same way. Crossing the belt into a figure-of-eight reverses the output, a simple way to change direction without gears, at the cost of extra rubbing where the belt crosses. A belt drive grips only by friction, so if the load is too large or the belt too slack, it slips: the measured output speed then falls below the value predicted from the diameters. Measuring that shortfall at different tensions shows clearly why belts must be correctly tensioned, and why a little slip can also protect a machine from sudden overload.

Specifications

Transmission Belt drive between pulleys
Speed ratio without slip n₂/n₁ = D₁/D₂
Configurations studied Open belt (same direction), crossed belt (reversed direction)
Measurements Turns counted, or speeds read with a tachometer or stroboscope
Pulley sizes, belt type and drive Confirm at enquiry

Applications

  • Calculating and checking speed ratios from pulley diameters
  • Comparing open and crossed belt arrangements
  • Measuring slip by comparing predicted and actual output speeds
  • Relating the fall in speed to the rise in output torque

Care & Handling

  • Release belt tension when the bench is stored so the belt does not take a permanent set.
  • Keep oil and grease off belts and pulley grooves, which make the belt slip.
  • Check belts for cracks or fraying and replace them when worn.
  • Keep fingers away from the point where the belt runs onto a pulley.

Why Choose LabEquip

Technology and engineering teachers use a belts and pulleys test bench to introduce mechanical transmission before moving on to chains and gears. LabEquip lists it with the other transmission benches, including the sprocket and chain test bench, in its range of physics lab equipment. Pulley sizes and belt options can be discussed through the contact page.

Frequently Asked Questions

How is the speed ratio of a belt drive calculated?

Take the driver’s diameter and divide it by the driven pulley’s diameter. A 30 mm pulley driving a 90 mm pulley makes the output turn at one third of the input speed, assuming no slip.

What does crossing the belt do?

It reverses the direction of the driven pulley. An open belt turns both pulleys the same way, while a crossed belt in a figure-of-eight makes them turn in opposite directions.

Why does the driven pulley turn slower than calculated?

The belt slips and stretches slightly under load, so the output falls short of the ideal speed. The difference grows when the belt is slack or the load is heavy.

How does belt tension affect the drive?

Too little tension lets the belt slip, while too much loads the bearings and wears the belt quickly. The correct tension transmits the load with little slip and a slight give when pressed.

What happens to torque when the speed is reduced?

In an ideal drive the power stays the same, so torque rises in proportion as speed falls. Reducing the speed to one third roughly triples the turning force, less the losses to friction.

Where are belt drives used in everyday machines?

Washing machines, sewing machines, pillar drills, car engine accessory drives and many conveyors use belts. They are quiet, cheap and tolerate small misalignments.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)