Search

In Stock

Gear Chain Test Bench

Banc d’essai pignon-chaîne, Integrated Tension Adjustment Mechanism Enables the technical Evaluation of frictional losses and transmission efficiency in relation to chain slack and alignment.

High-Visibility Dynamic Componentry supports the physical Application of rotational kinematics formulas, providing evidentiary-grade data acquisition for undergraduate research rotations.

Ruggedized Bearing Support Systems ensure laboratory Consistency across multi-year curriculum cycles by minimizing parasitic mechanical noise and shaft deflection.

₹2,374.00

Quick Answer: A sprocket and chain test bench is a teaching bench on which a roller chain carries rotation from one toothed sprocket to another, as on a bicycle. Students use the sprocket and chain test bench to work out speed ratios from tooth counts, confirm that both sprockets turn the same way and see how chain tension affects the drive.

Counting Teeth Instead of Measuring Diameters

Each link of the chain engages one tooth, so in any period the same number of teeth pass on both sprockets. The speed ratio follows directly: n₂/n₁ = T₁/T₂, where T is the number of teeth. A 44-tooth front sprocket driving an 11-tooth rear sprocket turns the rear four times for every turn of the front. On a bicycle with a wheel of circumference 2.1 m, that is 8.4 m travelled for each turn of the pedals.

Because the chain meshes with the teeth, it cannot slip the way a belt can. This positive drive keeps the ratio exact under heavy load, which is why chains are used where timing or high torque matters. The trade-off is the need for lubrication, some noise and wear that slowly lengthens the chain.

Direction and Tension

Both sprockets turn in the same direction, just as with an open belt. That contrasts with two gears meshing directly, which turn in opposite directions; the chain acts as a flexible link that carries the motion across a gap without reversing it. A chain should be fitted with a small amount of sag on its slack side. Too tight, and it loads the bearings and wears quickly; too loose, and it may jump teeth or come off under load.

Applications

  • Calculating speed ratios from tooth counts and checking them by counting turns
  • Comparing chain drives with belt drives and with directly meshing gears
  • Relating sprocket choice to bicycle gearing and distance per pedal turn
  • Observing the effect of chain sag on smooth running

Specifications

Transmission Roller chain over toothed sprockets
Speed ratio n₂/n₁ = T₁/T₂ (tooth counts)
Direction Both sprockets turn the same way
Slip None, since the chain meshes with the teeth
Sprocket sizes, chain type and drive Confirm at enquiry

Care & Handling

  • Keep the chain lightly oiled and wipe off the excess, which collects dirt.
  • Check the chain sag before use and adjust it if the chain is too tight or too slack.
  • Keep fingers well clear of the point where the chain meets a sprocket.
  • Store the bench clean and dry to prevent rust on the chain.

Why Choose LabEquip

Technology and engineering teachers pair a chain bench with a belt bench so students can compare friction drive with positive drive directly. LabEquip lists this sprocket and chain test bench in its physics lab equipment range together with the belts and pulleys test bench. Sprocket sizes can be agreed through the contact page.

Frequently Asked Questions

How is the speed ratio of a chain drive worked out?

Divide the number of teeth on the driving sprocket by the number on the driven sprocket. A 44-tooth sprocket driving an 11-tooth sprocket gives a ratio of four, so the output turns four times as fast.

Why does a chain not slip like a belt?

The chain’s rollers sit between the sprocket teeth, so the drive depends on meshing rather than friction. As long as the chain stays on the teeth, the ratio is exact.

Why do both sprockets turn the same way when meshing gears do not?

The chain wraps around both sprockets on the same side, carrying the motion across without reversing it. Two gears in direct contact push each other at the mesh, so they turn in opposite directions.

How does a bicycle use this principle?

The pedals turn the front sprocket and the chain drives a smaller rear sprocket fixed to the wheel. Changing to a smaller rear sprocket raises the ratio, so each pedal turn moves the bicycle further but needs more force.

How tight should the chain be?

It should have a little sag on the slack side when the drive is at rest. A chain that is too tight wears the bearings, while one that is too loose can jump teeth under load.

How should the chain be cleaned and lubricated?

Wipe off old grime with a cloth, apply a light chain oil to the rollers while turning the sprockets slowly, then wipe away the excess so it does not attract dust.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)