Search

In Stock

Pipette, Bulb Type (Clear Glass)

Volumetric Reservoir Geometry: Features a precision-blown central bulb designed to maximize volume-to-surface-area efficiency, minimizing liquid retention and drainage errors during delivery.

Calibrated "To Deliver" (TD) Matrix: High-contrast ceramic graduations are fire-fused into the glass at 20°C, ensuring permanent legibility and Class A/B volumetric accuracy through repetitive sterilization cycles.

₹300.00

Quick Answer: A bulb pipette, also called a volumetric or transfer pipette, is a clear glass tube with a single swollen bulb in the middle and one calibration mark on the upper stem. It delivers one fixed volume of liquid accurately, for tasks such as measuring aliquots for titration.

One Mark, One Volume

The bulb pipette holds most of its volume in the central bulb, leaving only narrow stems above and below. With the mark on the narrow upper stem, a small error in setting the meniscus is a tiny fraction of the total volume, which is why this design measures a single volume more accurately than a graduated pipette of the same size. It is the standard tool for transferring a measured aliquot of an unknown solution into a titration flask.

Volumetric pipettes of this kind are generally calibrated to deliver: the stated volume flows out when the pipette drains under gravity with its tip touching the wall of the receiving vessel, and the small drop left in the tip is allowed for in the calibration. It should not be blown out unless the pipette is marked for blow-out.

Clear glass lets the user watch the liquid rise into the upper stem and spot bubbles or droplets clinging inside, which signal grease and mean the pipette needs cleaning. Always fill it with a pipette filler or safety bulb, never by mouth.

Care & Handling

  • Rinse the pipette with a little of the solution to be measured before filling, and discard the rinsings.
  • Clean with detergent if drops cling to the inside; clean glass drains in an even film.
  • Do not dry the pipette at high oven temperatures, which can alter its calibration; let it drain dry or rinse it with propanone.
  • Store pipettes in a rack or drawer with the tips protected, since a chipped tip changes the delivery time and volume.

Applications

  • Measuring aliquots of acid or alkali into conical flasks for titration
  • Preparing standard solutions by transferring a measured volume into a volumetric flask for dilution
  • Dispensing water samples for hardness, alkalinity or chloride tests
  • Teaching quantitative technique in school and college practical courses

Specifications

Item Bulb (volumetric) pipette, single mark
Material Clear glass, as named in the title
Calibration One fixed volume, normally to deliver
Filling With a pipette filler or rubber safety bulb

Why Choose LabEquip

Every titration practical in a school or college course starts with a volumetric pipette, so they are ordered in class sets. LabEquip lists them in its chemistry lab equipment range with the graduated pipette for variable volumes; send capacities and quantities through the contact page.

Related Products

  • Pipette Filler, 3 way: A three-valve pipette filler for drawing up and releasing liquid in the pipette without mouth pipetting.
  • Pipette, Graduated: A graduated pipette for variable volumes when the method does not call for one fixed volume.
  • Borosilicate Volumetric Pipette: A borosilicate single-mark volumetric pipette for precise transfers in volumetric analysis.
  • Volumetric Flask: A volumetric flask for making the standard solution that the pipette then measures out.
  • Pipette Stand (Horizontal): A horizontal pipette stand to rest the pipette between aliquots with its tip off the bench.

Frequently Asked Questions

Should the last drop be blown out of a bulb pipette?

No. A bulb pipette of this kind is normally calibrated to deliver, and the small amount left in the tip after the liquid drains is already allowed for. Let it drain with the tip touching the inside of the receiving vessel, wait a few seconds, then remove it without blowing.

Why is a bulb pipette more accurate than a graduated pipette?

The clear glass bulb pipette holds most of its volume in the central bulb, and its single calibration mark is on the narrow upper stem. A small error in setting the meniscus there is a tiny fraction of the total volume, so it measures one fixed volume more precisely than a graduated pipette of the same size.

How do I set the meniscus exactly on the mark?

Draw the liquid a little above the mark with a pipette filler, wipe the outside of the tip, then let liquid out slowly until the bottom of the curved meniscus just touches the mark with your eye level with it. Touch the tip on the side of the beaker to remove the hanging drop.

Why must a bulb pipette never be filled by mouth?

Mouth pipetting risks swallowing or inhaling the solution, even when it looks harmless. Use a rubber safety bulb or a pipette filler to draw liquid up; it also gives better control when setting the meniscus.

What does it mean if drops stick to the inside of the pipette?

Drops clinging to the wall show that the glass is greasy, so the pipette will not deliver its full volume. Clean it with detergent solution and rinse thoroughly with distilled water; a clean pipette drains in a smooth, unbroken film.

Why rinse a bulb pipette with the solution before use?

Rinsing with a small portion of the solution to be measured removes water left from cleaning, which would otherwise dilute the first aliquot. Draw up a little, tilt and turn the pipette to wet the inside, discard it, and repeat once or twice.

Last Updated: November 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)