Quick Answer: The digital voltmeter 10V is a digital meter titled for 10 volts that displays the potential difference between two points in a circuit as a number. Connected in parallel across a cell, resistor or lamp, it suits the low-voltage circuits used in most school and college electricity practicals.
Measuring Potential Difference Digitally
A voltmeter compares the electrical potential at two points, so it is connected across a component rather than into the circuit. The circuit is built first and working, and then the voltmeter leads are clipped to either side of the component, positive lead to the side nearer the positive terminal of the supply. Nothing needs to be disconnected, which makes voltage readings quicker to take than current readings.
A good voltmeter draws almost no current. Digital voltmeters achieve this with a very high input resistance, so the meter hardly disturbs the circuit it measures. This matters in potential divider and internal resistance experiments: a low-resistance meter connected across a large resistor would itself carry current and give a reading lower than the true value.
A 10 V scale is well matched to school electricity. A few cells in series, a low-voltage power supply set to a few volts, the voltages across lamps, resistors and LEDs, and the emf of a single cell all fall within it. Matching the meter’s range to the voltages being measured shows them with more significant figures than a meter built for hundreds of volts.
Specifications
| Instrument | Digital voltmeter |
| Range | 10 V, as titled |
| Connection | In parallel across the component, observing polarity |
| Loading effect | Low, as digital voltmeters have a high input resistance |
| AC or DC type, resolution and power source | Confirm at enquiry |
Care & Handling
- Keep inputs to the digital voltmeter 10V within its range; connecting it across a higher voltage can damage it.
- Connect it across components, not in series, where its high resistance stops the circuit working.
- Switch the meter off after use, where it has a switch, to save its battery.
- Wipe the display with a dry cloth and keep the meter away from liquids on the bench.
Practical Uses
- Measuring the voltage across resistors and lamps in Ohm’s law and I–V experiments
- Finding the emf and terminal voltage of cells in internal resistance practicals
- Showing how voltage divides in series circuits and stays equal across parallel branches
- Measuring the output of potential dividers and solar cells
- Checking cells and low-voltage supplies before a practical
Why Choose LabEquip
Schools buying digital voltmeters for class sets usually choose a range near 10 V for cell and low-voltage practicals. For higher voltages LabEquip also lists a 200V digital voltmeter, and the 10A DC ammeter completes a power-measurement pair; all sit in the physics lab equipment range. Send requirements via the contact page.
Frequently Asked Questions
Why is a voltmeter connected in parallel?
Potential difference is the energy transferred per unit charge between two points, so the meter must touch both points. Connected in parallel across a component, it measures the voltage that component receives without changing the circuit.
What happens if the voltmeter is connected in series by mistake?
Its very high resistance blocks almost all current, so lamps go out and the meter reads close to the full supply voltage. No damage usually results, but the circuit will not work until the meter is reconnected across the component.
Why does a voltmeter read lower than expected across a large resistor?
If the meter’s resistance is not much larger than the resistor’s, some current flows through the meter and the voltage across the pair falls. Digital meters, with their high input resistance, reduce this loading effect greatly compared with simple analogue meters.
Can it measure the emf of a cell?
Nearly. Connected directly across a cell with nothing else attached, a high-resistance voltmeter draws so little current that the reading is very close to the emf. Once the cell supplies a load, the terminal voltage falls below the emf.
Why choose a 10 V meter rather than one with a higher range?
A meter whose range is close to the voltages being measured shows them with more significant figures. Cells and low-voltage supplies give a few volts, so a 10 V meter reads them more precisely than one designed for hundreds of volts.
What voltages appear across components in series?
The supply voltage is shared between them in proportion to their resistances. Measuring each and adding the readings gives the supply voltage, a direct check of energy conservation in circuits.
Last Updated: October 2026










Reviews
There are no reviews yet.