Quick Answer: A compound pendulum is a rigid bar with holes along its length that is swung from a knife edge passed through any one of the holes. Offered in steel, brass or stainless steel, it is used to determine the acceleration due to gravity and the bar’s radius of gyration.
Why a Bar Instead of a Bob
A simple pendulum assumes all its mass is at one point, an ideal that a real bob and string only approximate. A rigid bar is a real body whose mass is spread out, so its period depends on its moment of inertia about the point of suspension as well as on the distance from that point to its centre of gravity. Holes drilled at equal intervals along the bar let the suspension point be moved step by step.
Timing the oscillations from each hole on both sides of the centre gives two curves of period against distance. Each curve falls to a minimum and rises again, and the minimum occurs where the distance from the centre equals the radius of gyration. A horizontal line drawn across the graph cuts it at four points; pairs of these give the length of the equivalent simple pendulum, and g follows from that length and the corresponding period.
Points of suspension and oscillation are interchangeable: the bar swings with the same period from either point, a property that Kater’s reversible pendulum uses to measure g with high accuracy.
Specifications
| Type | Bar pendulum with holes along its length |
| Material options | Steel, brass or stainless steel |
| Suspension | Knife edge passed through a chosen hole |
| Quantities found | Acceleration due to gravity, radius of gyration |
| Bar dimensions and knife-edge support | Confirm at enquiry |
Steel, Brass or Stainless Steel
For a uniform bar of given dimensions, the period does not depend on the material, because mass appears in both the moment of inertia and the gravitational torque and cancels. The choice of material is therefore practical. Brass and stainless steel resist tarnish and rust in humid laboratories, while plain steel is a robust general choice; the material and the bar dimensions for the version ordered can be confirmed at enquiry.
Applications
- Determining g from the graph of period against distance from the centre of gravity
- Finding the radius of gyration and moment of inertia of the bar
- Showing that points of suspension and oscillation are interchangeable
- Comparing the result for g with that from a simple pendulum bob experiment
Care & Handling
- Keep the knife edge sharp and clean and the bar’s holes free of burrs, so the pivot friction stays low.
- Swing the bar through small angles only, and time twenty or more oscillations.
- Hang the bar or lay it flat in storage to keep it straight.
- Wipe plain steel bars with a lightly oiled cloth before storage to prevent rust.
Why Choose LabEquip
Colleges and senior schools buy the bar pendulum for their gravity and rotational-motion practicals, choosing steel, brass or stainless steel to suit their conditions. It is part of LabEquip’s physics lab equipment range, and the material and size can be agreed through our contact page.
Frequently Asked Questions
Does the material of the bar change the period?
Not for a uniform bar of the same dimensions. Mass appears in both the moment of inertia and the gravitational torque and cancels, so steel, brass and stainless steel bars of the same shape swing with the same period.
Why is the period plotted against distance from the centre?
The graph shows a minimum period at a distance equal to the radius of gyration and lets the length of the equivalent simple pendulum be read directly, from which g is found.
What is the equivalent simple pendulum length?
It is the length of a simple pendulum with the same period as the bar. On the graph it is the distance between two points of suspension on opposite sides of the centre that give the same period.
Why is the period never zero, even close to the centre?
As the pivot approaches the centre of gravity, the restoring torque becomes very small and the period grows large. The period is shortest at the radius of gyration, not at the centre.
Why use a knife edge rather than a pin?
A knife edge gives a sharp, well-defined pivot line with very little friction, so the measured distance to the centre of gravity is accurate and the oscillations die away slowly.
Which material should a school choose?
All three give the same physics. Brass and stainless steel resist corrosion in humid conditions, while plain steel is sturdy and suits general use.
Last Updated: October 2026










Reviews
There are no reviews yet.