Search

In Stock

Lift Pump

High-Clarity Borosilicate Barrel: Engineered with a precision-ground glass cylinder and a non-reactive piston assembly, allowing for unobstructed 360-degree observation of internal fluid dynamics and the functional sequence of the foot and piston valves.

Optimized Reciprocating Seal: Features a high-tolerance, leak-resistant cup-piston designed to maintain consistent vacuum pressure, effectively demonstrating the theoretical lift limit governed by local atmospheric pressure during manual suction cycles.

₹475.00

Quick Answer: The Lift Pump is a demonstration model of the common suction pump: a piston carrying its own valve moves in a barrel above a foot valve, and on each upstroke water above the piston is lifted to the outlet while more is drawn in below. The lift pump model shows that atmospheric pressure, not suction itself, raises water from a well.

Two Valves and a Moving Bucket

The lift pump has two one-way valves. The foot valve sits at the bottom of the barrel where the suction pipe enters, and the second is set in the piston, often called the bucket. On the upstroke the bucket valve is held shut by the water above it, so that water is carried up and flows out of the side outlet; at the same time the space below the bucket expands, its pressure falls, and atmospheric pressure on the water in the well pushes more water up through the foot valve.

On the downstroke the foot valve closes, stopping the water in the barrel from running back down, and the bucket valve opens so the piston slides down through the water, ending up beneath it ready for the next lift. The first few strokes only remove air from the suction pipe, which is why a lift pump often needs priming with a cupful of water to seal the valves. Glass teaching models with float valves let students see each valve open and close.

Because the water is pushed up by the atmosphere, a lift pump at the surface cannot lift water whose level is more than roughly ten metres beneath it, whatever the effort applied. That limit, and the different piston of the force pump, are the two key teaching points. The model’s material and size are not stated in the title. Magdeburg hemispheres give a dramatic second look at the same atmospheric pressure.

Applications

  • Explaining village hand pumps and suction pumps in lessons on air pressure
  • Comparing valve action with the force pump
  • Discussing why suction pumps cannot raise water from deep wells
  • Demonstrating priming and the importance of a good seal

Specifications

Type Lift (suction) pump demonstration model
Valves Foot valve in the barrel and a valve in the piston
Delivery From an outlet near the top of the barrel on the upstroke
Principle Atmospheric pressure raises water into the barrel
Material and size Confirm at enquiry

Care & Handling

  • Prime the barrel with water before use so the valves seal.
  • Stand the source container below the barrel and keep the end of the suction tube under water.
  • Drain the model completely after the lesson and let the valves dry before storage.
  • Inspect the valves for wear or debris if the pump loses its prime.

Why Choose LabEquip

Primary and secondary science teachers use the lift pump model to connect air pressure with a machine students have seen in daily life. Find it with our Physics Equipments and contact LabEquip to confirm the model details.

Frequently Asked Questions

Does a lift pump really suck water up?

Not in the strict sense. The upstroke lowers the pressure in the barrel, and atmospheric pressure acting on the water outside pushes it up the pipe into the space.

Why can’t a lift pump raise water from very deep wells?

The atmosphere can balance a water column of roughly ten metres and no more. If the water lies deeper than that below the pump, no amount of pumping will bring it up.

What is the valve in the piston for?

It lets the piston pass down through the water in the barrel on the downstroke, then closes on the upstroke so that the water above the piston is lifted to the outlet.

Why does the pump need priming?

Dry valves leak air, so the upstroke cannot lower the pressure enough. Pouring a little water into the barrel seals the valves and lets the pump start drawing water.

How does a lift pump differ from a force pump?

In the lift pump, water passes up through a valve in the piston and leaves near the top of the barrel on the upstroke. The force pump’s piston is solid; it drives water through a separate outlet valve on the downstroke and can therefore deliver against a much greater height.

When does the water flow out of the outlet?

On the upstroke, when the closed piston valve carries the water above it to the level of the outlet. On the downstroke no water flows out, so the delivery comes in bursts.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)