Quick Answer: The Rigidity Apparatus (Searle’s Pattern) finds the modulus of rigidity of a wire by Searle’s method, in which the wire under test joins two identical metal bars hung by threads and the periods of their oscillations are measured. The same set-up also gives Young’s modulus and Poisson’s ratio for the wire.
Searle’s Two-Bar Method
In Searle’s arrangement two identical bars hang horizontally side by side from threads, and the specimen wire is screwed between their midpoints. Two kinds of oscillation are used. Swinging the free ends of the bars towards and away from each other bends the wire into an arc, and the period T1 of this motion depends on the wire’s Young’s modulus. Clamping one bar and letting the other twist about the wire as an axis gives torsional oscillation, with a period T2 that depends on the modulus of rigidity.
Both moduli follow from the same form of equation, 8πIl/(r⁴T²), where I is the moment of inertia of one bar about its centre, l the length of wire between the bars and r its radius: with T1 it gives Young’s modulus Y and with T2 the modulus of rigidity η. Dividing one by the other cancels most measured quantities, so Poisson’s ratio follows from the periods alone, σ = T2²/(2T1²) – 1.
Because the radius enters to the fourth power, the wire diameter must be measured carefully at several places with a micrometer screw gauge. The number of bars and wires supplied, their materials and the bar length are not stated in the listing title. The Poisson’s ratio of rubber apparatus gives a contrasting static method for a highly elastic material.
Specifications
| Method | Searle’s dynamic two-bar method |
| Specimen | Wire joined between the midpoints of two identical bars |
| Measured | Bending period T1 and torsional period T2 |
| Results | Young’s modulus, modulus of rigidity and Poisson’s ratio |
| Bars, wires and materials supplied | Confirm at enquiry |
Experiments
- Determining the modulus of rigidity of a wire from torsional oscillations
- Determining Young’s modulus of the same wire from bending oscillations
- Calculating Poisson’s ratio from the ratio of the two periods
- Comparing the elastic constants of wires of different metals
Care & Handling
- Keep the specimen wire straight and free of kinks; a bent wire gives wrong periods.
- Hang the bars level and at the same height, with threads of equal length.
- Use small amplitudes and stop the bars from colliding.
- Record each bar’s mass and dimensions before the practical, since they are needed for its moment of inertia.
Why Choose LabEquip
Degree-level physics laboratories buy Searle’s pattern apparatus because one set-up yields three elastic constants and gives practice in timing oscillations accurately. LabEquip lists it in Physics Equipments; confirm the bars and wires included through our contact page.
Frequently Asked Questions
What is the modulus of rigidity?
It is the ratio of shear stress to shear strain for a material, describing how strongly it resists twisting. For a wire, a higher modulus of rigidity means a larger couple is needed to twist it through a given angle.
Why does Searle’s method use two kinds of oscillation?
Bending the wire and twisting it test different elastic properties. The bending period gives Young’s modulus and the twisting period gives the modulus of rigidity, and comparing them gives Poisson’s ratio from a single specimen.
How is the moment of inertia of a bar found?
Weigh the bar and measure its length and width. For a rectangular bar turning about an axis through its centre at right angles to its length, the moment of inertia is one twelfth of its mass times the sum of the squares of its length and width.
Why must the wire radius be measured so carefully?
The radius appears to the fourth power in the formula, so a one per cent error in the radius gives about a four per cent error in the modulus. Take several micrometer readings along the wire in two perpendicular directions.
What amplitude of oscillation should be used?
A small one. Large swings stretch the threads, make the bars collide and spoil the simple harmonic motion the formula assumes. Displace the bars only slightly and time at least twenty oscillations.
Is this a static or a dynamic method?
It is a dynamic method, because the moduli come from periods of oscillation rather than from steady deflections under load. Static torsion apparatus, by contrast, measures the angle of twist produced by a known couple.
Last Updated: October 2026










Reviews
There are no reviews yet.