Search

In Stock

Ticker Tape Timer, AC Type

Standardized Frequency Sync: Designed to work perfectly with standard AC frequencies, providing a reliable time base of 50 or 60 dots per second without the need for manual calibration.

Low Friction Design: Features a smooth tape guide path to minimize mechanical resistance, ensuring that the timer itself does not significantly interfere with the motion of the trolley or falling mass being studied.

₹1,115.00

Quick Answer: The Ticker Tape Timer, AC Type is a motion-recording device in which a steel strip vibrates in step with a low-voltage alternating supply and prints evenly timed dots on a paper tape pulled by a moving object. An AC ticker tape timer lets students measure displacement, velocity and acceleration from the dot spacing.

Dots in Step with the Supply

Inside the timer, an alternating current in a coil magnetises a thin steel strip, usually with a permanent magnet alongside, so the strip is pulled one way and then the other in step with the supply. A striker on the strip presses a carbon disc against the tape at each vibration. On a 50 Hz supply, a timer built this way makes 50 dots every second, one every 0.02 s; designs without the permanent magnet mark at twice the supply frequency, so time a known run to confirm the dot rate of the unit in use.

The advantage of the AC type is that its timing is set by the supply frequency, which the electricity grid holds steady, rather than by an adjustable contact. Students can therefore treat the interval between dots as known and concentrate on distances. It must run only from the low-voltage output of a laboratory power supply at the voltage marked on the timer, never directly from the mains.

The tape is threaded under the carbon disc and attached to a trolley, usually running down a slightly tilted runway whose slope just balances friction. Cutting the tape into strips of equal dot count and pasting them side by side produces a velocity-time chart. For a comparison with electronic data logging, the same motion can be recorded with a wireless motion sensor; the regular type ticker timer is the other pattern in this range.

Specifications

Operating principle Vibrating steel strip driven by an alternating supply
Marking Striker and carbon disc printing dots on paper tape
Dot interval Linked to the supply frequency; verify with a timed run
Power Low-voltage AC from a laboratory supply, at the rating marked on the unit
Used with Ticker tape, carbon discs, trolley and runway
Operating voltage and mounting clamp Confirm at enquiry

Applications

  • Measuring the acceleration of a trolley on an inclined runway
  • Showing uniform velocity once the runway slope compensates for friction
  • Investigating Newton’s second law by varying the pulling force and the mass
  • Estimating g from a falling mass pulling tape, with friction discussed as an error

Care & Handling

  • Switch off before threading tape or changing the carbon disc.
  • Keep the tape path straight and the tape under the disc, so dots print cleanly.
  • Replace dried or worn carbon discs; faint dots are easy to miscount.
  • Clamp the timer firmly to the bench so it does not shift with the pulled tape.

Why Choose LabEquip

Ticker timers remain a staple of mechanics lab equipment in secondary physics, because every group gets a permanent record of its own run to analyse. LabEquip lists this AC model in the General Lab Products range; send the number of runways you are equipping through the contact page.

Frequently Asked Questions

How many dots per second does an AC ticker tape timer make?

It depends on the supply frequency and the design. A polarised timer on a 50 Hz supply makes 50 dots per second, while a design without a permanent magnet can make 100. Check by running tape for a timed period and counting the dots.

How is velocity found from the tape?

Measure the distance covered over a set number of dot intervals and divide by the time those intervals represent. For example, 10 intervals at 0.02 s each is 0.2 s, so a 5 cm length gives an average velocity of 25 cm/s.

Can it be plugged directly into the mains?

No. Run it only from the low-voltage AC output of a laboratory power supply, at the voltage marked on the timer. Mains voltage would damage the coil and create a serious shock hazard.

Why do the first few dots look crowded?

At the start the trolley is still speeding up from rest, so the dots are close together, and they may overlap where the timer printed before motion began. Ignore the first few and begin measuring from a clear dot.

What causes missing or double dots?

Missing dots usually mean a dry carbon disc, tape running above the disc, or a striker set too high. Double dots come from a loose strip or a tape that flutters. Adjust the striker and keep the tape taut and straight.

How do I make a velocity-time chart from the tape?

Cut the tape into consecutive strips, each containing the same number of dot intervals, and stick them side by side on paper in order. Each strip’s length is proportional to average velocity, so the tops of the strips trace the velocity-time graph.

Last Updated: September 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)