Search

In Stock

Threaded Olive Fitting for Minitop Entry

Raccord d'entrée olive crantée pour Minitop Features a precision-contoured "olive" barb that provides multiple high-friction contact points, ensuring a gas-tight mechanical seal with flexible laboratory tubing without the need for external hose clamps.

High-Purity Nickel-Plated Brass Constructed from industrial-grade alloy for superior corrosion resistance and thread longevity, ensuring a non-reactive flow path compatible with high-purity oxygen and inert laboratory gases.

$1.80

Quick Answer: This is a brass hose tail fitting for the Minitop gas connection: a threaded union nut, a serrated hose tail that flexible tubing pushes onto and, in the product photograph, two hose clips that lock the tubing in place. The hose tail fitting for Minitop lets a small Minitop gas bottle feed apparatus through ordinary laboratory gas tubing.

Parts of the Fitting and What Each Does

The hose tail fitting for Minitop has three working parts. The union nut carries the thread that screws onto the Minitop connection and draws the fitting against its seat. The hose tail is the ridged brass spigot: its serrations bite into the bore of soft tubing so the tube resists being pulled off. The clips shown in the photograph squeeze the tubing over the serrations, turning a push fit into a joint that holds under the gas pressure in use.

Brass is the usual material for small gas fittings because it machines cleanly, resists corrosion in air and is generally regarded as non-sparking; those are properties of brass in general, not a rating for this fitting.

Specifications

Product Hose tail fitting for a Minitop gas connection
Parts in photograph Threaded union nut, serrated brass hose tail, two hose clips
Material, as pictured Brass nut and hose tail; metal clips
Joint type Threaded connection on the Minitop side; push-on tubing secured by clips
Used with Minitop gas bottle and flexible gas tubing
Thread and hose tail size Confirm at enquiry

Fitting Tubing to a Hose Tail

Choose tubing whose bore is a snug fit on the hose tail: too loose and the clip has to do all the work, too tight and the tube splits. Warming the end of rubber or PVC tubing in hot water softens it so it slides fully over the serrations. Slide the clip onto the tube first, push the tube on as far as it goes, then position the clip over the serrations and close it.

Screw the union nut on by hand to start the thread, then tighten it with a spanner without excessive force. With gas on at working pressure, brush soapy water or leak-detection fluid over the nut and the tube end; a joint that bubbles is remade before the apparatus is used.

Care & Handling

  • Keep fittings used on oxygen free of oil, grease and any thread sealant not intended for oxygen
  • Replace tubing that has hardened or cracked at the hose tail rather than trimming and refitting it repeatedly
  • Check the union nut seat for dirt or damage before each fitting
  • Leak-test with soapy water after every reconnection

Typical Uses

  • Connecting a Minitop oxygen bottle to tubing that leads to a gas jar, burner or reaction vessel
  • Replacing a worn or split tubing connection on an existing Minitop set-up
  • Showing students how a ridged spigot and a clip make a pull-resistant gas joint

Why Choose LabEquip

Schools that run oxygen and combustion demonstrations from a refillable Minitop oxygen bottle need spare connection parts that match it. LabEquip supplies the fitting with the related gas pipe and other physics lab equipment; to check the thread before ordering, contact LabEquip.

Frequently Asked Questions

What is a hose tail?

A hose tail is a ridged spigot that flexible tubing is pushed onto. The ridges grip the inside of the tube and a clip around the outside holds it there, so the tubing stays on when gas flows through it.

Why are hose clips included in the photograph?

Ridges alone can let tubing creep off under pressure or when the tube is pulled. A clip squeezes the tubing onto the ridges, which makes the joint much harder to pull apart and reduces the chance of a leak.

Should I use thread tape on the union nut?

A union nut that seals on a seat does not normally need tape, and on oxygen equipment only sealants intended for oxygen should ever be used. If the joint leaks, inspect the seat for dirt or damage before adding anything.

How do I fit tubing that is a tight fit?

Dip the tube end in hot water for a short time to soften it, then push it on with a twisting motion. Never use oil or grease as a lubricant on a gas fitting, especially one used for oxygen.

Can this fitting be used with other gas bottles?

It is intended for the Minitop connection named in its listing. Other bottles and regulators may use different threads, so make sure the thread matches before connecting it to anything else.

How do I know the joint is gas-tight?

Turn the gas on at working pressure and brush soapy water over the nut and the tube end. Bubbles that grow show a leak. Turn the gas off, remake the joint and test again before running the experiment.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)