Quick Answer: The sync cable for fast camera use is a synchronisation lead for the Jeulin fast camera. It carries a trigger signal between the camera and external apparatus, so that a high-speed recording starts, or is marked, at the instant of an event such as a release, an impact or a burst, rather than when someone presses a button.
Why High-Speed Video Needs a Trigger
A camera running at a high frame rate fills its memory quickly, so each recording covers only a short stretch of time. Many of the events worth filming in a physics lesson last a few milliseconds: a ball striking a plate, a water drop splashing, two carts colliding. Human reaction time is around a fifth of a second, far longer than the event, so starting the camera by hand often means the action happens before or after the recorded window.
A synchronisation cable solves this by letting the experiment tell the camera when to act. A release mechanism, a light barrier or another sensor produces an electrical signal at a known moment, and the cable carries that signal to the camera’s sync connection. The frame in which the event appears is then tied to a definite instant, which matters when the video is used to measure speeds and accelerations.
Specifications
| Item | Synchronisation (trigger) cable |
| For use with | Jeulin fast camera, as titled |
| Purpose | Links the start or marking of a recording to an external signal |
| Typical trigger sources | Release mechanisms, light barriers, impact sensors |
| Connector types and length | Confirm at enquiry |
Setting Up a Triggered Recording
Connect the cable with the camera and the triggering device switched off, then frame the shot and set the recording mode. Arm the camera, start the experiment and let the signal begin the capture. Before relying on the arrangement for measurement, film a simple test, such as a small lamp switched by the same trigger signal, and count how many frames pass between the signal and the lamp lighting; that tells you whether any delay needs to be allowed for.
Applications
- Filming a falling ball as it leaves an electromagnet release
- Capturing collisions between carts at the moment of contact
- Recording splashes, bursting balloons and other events lasting milliseconds
- Matching video frames to a known instant for kinematics measurements
Care & Handling
- Hold the plug, not the lead, when disconnecting, and never let the cable carry the weight of the camera.
- Coil the cable loosely for storage; tight kinks break the conductors inside.
- Route the cable away from moving carts, falling masses and launchers so it is not snagged during a run.
- Inspect the connector pins before use and keep the cable with the camera kit so it is not lost.
Why Choose LabEquip
Schools and colleges that already run the Jeulin fast camera order this lead when they move from hand-started clips to measured, triggered recordings. LabEquip lists it with the educational camera in its physics lab equipment range. Use the contact page to check the connector type against your camera before ordering.
Frequently Asked Questions
Why use a trigger cable instead of starting the camera by hand?
Human reaction time is around a fifth of a second, while many collisions and impacts last only a few milliseconds. A hand-started recording can easily miss the event, but a trigger signal starts or marks the recording at the moment the experiment produces it.
What kinds of experiment benefit from synchronised recording?
Short, one-off events gain most: a ball released from an electromagnet, carts colliding, a drop hitting water, a balloon bursting or a spring being released. Slow, repeating motions such as a pendulum can usually be filmed without a trigger.
Will the cable work with other cameras?
It is made for the Jeulin fast camera named in the title. Other cameras use different connectors and signal levels, so compatibility with another model should not be assumed.
How can I check the delay between the trigger and the recording?
Film a small lamp or LED switched by the same signal that triggers the camera, then count the frames between the trigger and the light appearing. Dividing that number by the frame rate gives the delay in seconds.
How many frames will a fast event cover?
Multiply the frame rate by the duration of the event. An impact lasting 4 milliseconds covers only four frames at 1000 frames per second, which is why the recording window has to be placed accurately with a trigger.
How should the cable be stored?
Coil it loosely without tight bends, keep the connectors clean and dry, and store it in the camera case. Pulling on the lead to unplug it is the most common cause of failure.
Last Updated: October 2026










Reviews
There are no reviews yet.