Quick Answer: Specific charge of the electron apparatus is a teaching set-up for measuring e/m, the ratio of the electron’s charge to its mass. In the usual form an electron beam is accelerated through a known voltage and bent into a circle by the uniform magnetic field of a pair of Helmholtz coils, and e/m is calculated from the voltage, the coil current and the radius of the circle.
How the Circular-Beam Method Works
Electrons leaving a heated cathode are accelerated through a potential difference U, so each one gains kinetic energy eU = ½mv². When the beam enters a magnetic field B at right angles to its motion, the magnetic (Lorentz) force evB acts sideways and supplies exactly the centripetal force mv²/r needed for circular motion. Eliminating the speed v from these two equations leaves e/m = 2U/(B²r²), so only the voltage, the field and the radius have to be measured.
A result within a few percent of the accepted 1.76 × 10¹¹ C/kg repeats the measurement that showed cathode rays to be particles far lighter than any atom.
Taking Readings for the Specific Charge of the Electron
The room is darkened so the faint glowing ring of the beam can be seen. A small amount of gas at low pressure is normally left in this type of tube; a few electrons collide with gas atoms, which then give out light and trace the path. The diameter of the ring is read against a scale or a mirror scale, with the eye lined up to avoid parallax, and halved to give r.
Two series of readings work well. Keeping the coil current fixed and raising U makes the circle larger, and a graph of r² against U is a straight line through the origin. Keeping U fixed and increasing the current shrinks the circle, because r is inversely proportional to B. The field between Helmholtz coils follows from B = (4/5)^(3/2) μ₀NI/R, where N is the number of turns on each coil and R their radius, or it can be measured directly with a teslameter probe.
Specifications
| Experiment | Specific charge of the electron, e/m |
| Method | Circular beam path in a uniform magnetic field |
| Working relation | e/m = 2U/(B²r²) |
| Field source in the usual set-up | Pair of Helmholtz coils |
| Readings | Accelerating voltage U, coil current I, beam radius r |
| Components and power supplies included | Confirm at enquiry |
Practical Work
- Determining e/m from the radius of the electron’s circular path
- Showing that a magnetic force on a moving charge acts at right angles to its velocity
- Plotting r² against accelerating voltage to test the theory
- Comparing the measured ratio with the accepted value as an exercise in error analysis
Care & Handling
- Follow the tube’s operating sequence: heater supply on first, then the accelerating voltage, and the reverse order when shutting down.
- Make or change every connection with all supplies switched off, using shrouded safety leads, because the tube runs at voltages that can give a dangerous shock.
- The tube is an evacuated glass vessel; keep it in its holder, never knock or clamp it hard, and carry it with both hands.
Why Choose LabEquip
University physics departments and senior secondary schools usually order this apparatus for a modern-physics practical alongside other electron-beam experiments. It sits in LabEquip’s range of physics lab equipment, which also lists e/m by Thomson’s bar magnet method for laboratories that run both techniques. Details of the coils, supplies and tube for your bench can be agreed through the LabEquip contact page.
Frequently Asked Questions
What is meant by the specific charge of the electron?
It is the charge-to-mass ratio, e/m, of the electron, about 1.76 × 10¹¹ C/kg. A beam experiment can measure only this ratio, because the bending of the path depends on charge and mass together. Combining it with Millikan’s value of e gives the electron’s mass.
Which formula is used in the circular-beam method?
The accelerating voltage gives eU = ½mv², and the magnetic force provides the centripetal force, so evB = mv²/r. Eliminating v gives e/m = 2U/(B²r²), where U is the accelerating voltage, B the magnetic flux density and r the radius of the circle.
How is the magnetic field between Helmholtz coils found?
For two coils separated by their radius R, each with N turns carrying current I, the field near the centre is B = (4/5)^(3/2) μ₀NI/R and is close to uniform. The field can also be checked directly with a teslameter probe placed where the beam runs.
Why does the electron path show up as a glowing ring?
The tube holds a small amount of gas at low pressure. A few electrons strike gas atoms and excite them, and the atoms give off light as they return to their normal state. So few electrons collide that the beam keeps a sharp, visible outline.
Which errors affect the result most?
The radius enters as r², so a small reading error in the ring diameter doubles in percentage terms in e/m. Parallax, the Earth’s magnetic field adding to or subtracting from the coil field, and a field that is less uniform away from the centre of the coils also shift the result.
How does this method differ from Thomson’s crossed-field method?
Thomson balanced an electric deflection against a magnetic one to find the speed of the electrons and then used the size of one deflection. The circular-beam method takes the energy straight from the accelerating voltage and needs only the magnetic field and the radius, so it uses fewer quantities.
Last Updated: October 2026










Reviews
There are no reviews yet.