Quick Answer: The Hofmann Voltameter, named after the German chemist August Wilhelm von Hofmann, is a three-limbed glass apparatus for the electrolysis of water. Hydrogen and oxygen collect separately in the two side limbs above the electrodes, so their volumes can be compared and each gas tested.
How the Apparatus Separates the Two Gases
The apparatus is named after the German chemist August Wilhelm von Hofmann. Two vertical side tubes, each closed at the top by a tap, are joined near the bottom to a central tube that ends in a reservoir. An electrode is sealed into the foot of each side tube. Electrolyte is poured into the reservoir with the taps open until the side tubes are full, and the taps are then closed.
When a direct current flows, hydrogen forms at the cathode (negative) and oxygen at the anode (positive). Each gas rises into its own tube and pushes the liquid down and up into the central reservoir. The volume of hydrogen is very close to twice the volume of oxygen, matching the formula H2O, and the volumes are read from the graduations normally marked on the side tubes.
Pure water conducts too poorly for useful electrolysis, so a little dilute sulfuric acid or a salt such as sodium sulfate is added. The electrodes are traditionally platinum because it is not attacked; the electrode material and tube capacity are not stated in the listing title. Inexpensive graphite electrodes such as the electrolysis carbon rod are used for other school electrolysis demonstrations.
Experiments
- Electrolysis of water and the two-to-one volume ratio of hydrogen to oxygen
- Testing hydrogen with a lighted splint and oxygen with a glowing splint
- Relating the charge passed, from current and time, to the volume of gas: Faraday’s laws
- Investigating how the current affects the rate of gas production
Specifications
| Apparatus | Hofmann voltameter, three-limbed |
| Construction | Two side tubes with taps, joined to a central reservoir tube |
| Electrodes | One sealed into the foot of each side tube |
| Electrolyte | Water made conducting with dilute acid or a salt |
| Electrode material and tube capacity | Confirm at enquiry |
Care & Handling
- Support the voltameter in a clamp and stand; it is tall and easily knocked over.
- Use a low-voltage DC supply only.
- Keep flames away from the taps except during a controlled splint test, since hydrogen and oxygen together are explosive.
- Drain and rinse with water after use rather than leaving acid in the tubes, and grease the taps sparingly.
Why Choose LabEquip
Physics and chemistry departments buy the Hofmann voltameter for the electrolysis of water, one of the few practicals where students can measure the composition of a compound by volume. LabEquip lists it under Physics Equipments; use our contact page to confirm electrode material and size.
Frequently Asked Questions
How should the voltameter be filled before a run?
Open both taps, pour the electrolyte into the central reservoir until the two side limbs are full right up to the taps with no air trapped, then close the taps before the supply is switched on.
Why is twice as much hydrogen produced as oxygen?
Each water molecule contains two hydrogen atoms and one oxygen atom. Electrolysis releases them as hydrogen and oxygen gas, and equal numbers of gas molecules occupy equal volumes, so two volumes of hydrogen form for each volume of oxygen.
What electrolyte should be used?
Water with a small amount of dilute sulfuric acid is the traditional choice, and sodium sulfate solution is a gentler alternative for younger classes. Avoid sodium chloride, which gives chlorine at the anode instead of oxygen.
How are the collected gases tested?
Hold an inverted test tube over a tap, open the tap briefly to release the gas into it, then test. Hydrogen burns with a squeaky pop when a lighted splint is brought near; oxygen relights a glowing splint.
What supply does the voltameter need?
A low-voltage DC supply, such as a battery or the DC output of a school power pack. Connect the negative terminal to the electrode where hydrogen should collect. An ammeter in series lets students relate the charge passed to the gas volume.
Why are the gas volumes not exactly two to one at first?
Oxygen dissolves in water more readily than hydrogen does, and some can react at the anode, so the oxygen volume reads slightly low early in the run. Letting electrolysis continue for a while before taking readings brings the ratio closer to two to one.
Last Updated: October 2026










Reviews
There are no reviews yet.