Search

In Stock

Digital Resistance Meter 20 kΩ

Original price was: ₹850.00.Current price is: ₹415.00.

Quick Answer: This digital resistance meter is an ohmmeter with a range designated 20 kΩ that shows the resistance of a component, taken out of a powered circuit, as a direct numerical reading. Physics and electronics labs use it to check resistor values, series and parallel combinations, and sensors such as thermistors and LDRs.

How a Digital Resistance Meter Measures

A digital ohmmeter passes a small, known test current through the component and measures the voltage that appears across it. By Ohm’s law the resistance is that voltage divided by the current, and the meter displays the result directly, so students avoid the crowded, right-to-left scale of an analogue ohmmeter.

Because the meter supplies its own current, the component must be disconnected from any power source, ideally with one end lifted out of circuit. Any parallel path, including fingers holding both leads, carries part of the test current and makes the reading too low.

What the 20 kΩ Range Means

On digital meters a range named 20 kΩ conventionally covers readings up to just below 20 kΩ; on a common 3½-digit display that means 19.99 kΩ, in steps of 10 Ω. Whether this meter has that range alone or others too should be confirmed. Above full scale, many meters show an overload sign, often a lone 1 at the left, instead of a value.

That makes the range well suited to school resistors from a few hundred ohms up to about 20 kΩ, and to thermistors and LDRs under room conditions. It suits very low resistances poorly: a metre of resistance wire of a few ohms cannot be read usefully in 10 Ω steps, so resistivity work is better done on a meter bridge (Wheatstone bridge) with pencil jockey.

Specifications

Item Digital resistance meter (ohmmeter)
Range designation 20 kΩ, as given in the product name
Measured quantity Resistance of components with no power applied
Principle Known test current applied, voltage measured, resistance shown digitally
Other ranges, resolution and power source Confirm at enquiry

Uses in the Lab

  • Checking resistor values against their colour code before a circuit practical
  • Verifying series and parallel combination formulas by measuring resistors singly and together
  • Following an NTC thermistor’s resistance as it is warmed in a water bath
  • Showing how an LDR’s resistance falls as more light reaches it
  • Continuity checks on leads, switches and plug-in components

Care & Handling

  • Never connect the meter to a live circuit; switch off and discharge any capacitors first
  • Touch the probes together before measuring to check that the display reads at or near zero and the leads are intact
  • Hold components by their bodies or use crocodile clips, not fingers on both ends
  • Switch the meter off after use, and remove the battery before long storage if it runs on one

Why Choose LabEquip

Schools and colleges choose a dedicated digital resistance meter when they want a simple instrument for resistor and sensor practicals, without the many switch positions of a multimeter. It is listed in LabEquip’s electrical and electronics range; contact LabEquip to confirm its ranges, display and power source before ordering class sets.

Frequently Asked Questions

Can the meter measure resistance in a working circuit?

No. It drives its own test current through the component, so the circuit must be switched off and capacitors discharged. For an accurate value, disconnect at least one end of the component so that the rest of the circuit cannot form a parallel path.

What happens if the resistance is above 20 kΩ?

The meter cannot show a value above the top of its range and displays an overload indication instead. Use a higher range or another meter for components such as an LDR in darkness or a high-value resistor.

Why does my reading change when I hold the resistor?

Your body forms a second path in parallel with the resistor. At tens of kilohms that path is no longer negligible, so the reading drops. Use crocodile clips or hold the component by its body only.

Is this meter suitable for measuring resistance wire?

Only roughly. Short lengths of resistance wire measure a few ohms, too little for a range intended for kilohm values. A meter bridge or a potentiometer method gives much better precision in resistivity experiments.

How closely should a resistor match its colour code?

The tolerance band sets the limit, commonly 5 percent for gold or 1 percent for brown. A 10 kΩ resistor with a gold band may read anywhere from 9.5 to 10.5 kΩ and still be within specification, and measuring a batch shows students that spread in practice.

Why use a digital meter instead of an analogue ohmmeter?

An analogue ohmmeter has a crowded, non-linear scale that reads from right to left and needs zero adjustment for each range. A digital meter shows the value directly, which removes interpolation errors and lets students record many readings quickly.

Last Updated: October 2026

Bestsellers

Portable Wheatstone Bridge

Original price was: ₹2,800.00.Current price is: ₹1,390.00.
(0 Reviews)

Step Down Transformer ( For Sonometer Experiment)

Original price was: ₹1,200.00.Current price is: ₹590.00.
(0 Reviews)

Solar Cell Performance Analysis Apparatus

Original price was: ₹2,200.00.Current price is: ₹1,090.00.
(0 Reviews)

Digital PN Junction Diode Characteristics Trainer

Original price was: ₹2,700.00.Current price is: ₹2,340.00.
(0 Reviews)

Resistive Load Bank Unit

Original price was: ₹10,000.00.Current price is: ₹4,990.00.
(0 Reviews)

Sodium Lamp Transformer 35W

Original price was: ₹3,300.00.Current price is: ₹1,640.00.
(0 Reviews)

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)