Search

In Stock

Double Pan Balance (Roberval Type)

Vertical Stabilizing Parallelogram Linkage: Engineered with precision-aligned steel pivots that ensure pans remain perfectly horizontal throughout the weighing cycle, eliminating measurement error regardless of specific weight placement on the pan surface.

Reinforced Cast-Iron Structural Frame: Built with a vibration-damping chassis and corrosion-resistant powder coating, providing a stable center of gravity and long-term mechanical durability for high-frequency laboratory duty cycles and rigorous handling.

₹1,000.00

Quick Answer: The Double Pan Balance (Roberval Type) is a two-pan mechanical balance in which the pans sit on top of a parallelogram linkage instead of hanging from the ends of a beam. A Roberval balance compares an object against known weights, and its linkage keeps both pans level so the result does not depend on where the load is placed.

The Parallelogram Behind the Pans

An ordinary beam balance hangs its pans from knife-edges at the ends of the beam, which keeps each load directly below its pivot. In 1669 Gilles Personne de Roberval presented a different arrangement: two horizontal beams, one above the other, joined at their ends by two vertical posts. The four parts form a parallelogram, so when the beams tilt the posts stay upright, and the pans can be mounted on top of the posts where they are open and easy to load.

The surprising property, often called Roberval’s paradox, is that a mass near the outer edge of a pan balances exactly as one at its centre. An off-centre load does try to twist its post, but the upper and lower beams resist that twist with equal and opposite horizontal forces. Those forces act along the beams, through their central pivots, so they produce no turning effect on the balance. Only the vertical load counts, which is why the balance stays fair when goods are dropped anywhere on the pan.

Reading the Balance

The object goes on one pan and known weights on the other until the pointer settles at the centre mark. On counter-scale versions a pointer rises from the linkage in front of a small scale, so the balance point is easy to see from across a counter. The method is the same comparison of masses as on any equal-arm balance, so the result does not depend on gravity; it is limited by the accuracy of the weights and by friction in the pivots.

Where It Is Used

  • Weighing produce, ingredients or materials by comparison with known weights
  • Teaching the equal-arm lever and the difference between comparing masses and measuring force
  • Demonstrating Roberval’s paradox by moving a load from the centre to the edge of a pan
  • Primary and middle-school activities on balancing, estimating and comparing masses

Specifications

Type Mechanical double pan balance, Roberval (parallelogram) type
Pans Two, carried above the linkage
Indicator Pointer showing the balance point
Weighing method Comparison against known weights
Capacity, pan material and weights supplied Confirm at enquiry

Care & Handling

  • Set the Roberval balance on a firm, level surface and check that the empty pans balance before weighing; use the zero adjuster if the model has one.
  • Load and unload the pans gently, because slamming weights down wears the pivots and can bend the linkage.
  • Keep the pivots clean and dry, and do not oil them unless the design calls for it, since oil collects dust.
  • Store the balance with the pans empty and covered against dust.

Why Choose LabEquip

Shops, school kitchens and science departments use this pattern because loads can be placed quickly on open pans. LabEquip lists it in its physics lab equipment range, and a weight set such as the knobbed brass masses set completes it for comparison weighing. Ask about the capacity and weights you need via the contact page.

Frequently Asked Questions

What is the difference between a Roberval balance and a beam balance?

In a beam balance the pans hang below the ends of a single beam. In a Roberval balance the pans sit above a parallelogram of two beams and two posts, which keeps them level and open. Both compare masses on equal arms; the Roberval pattern is easier to load but has more pivots, and so a little more friction.

Why does it not matter where the load sits on the pan?

The parallelogram keeps each post vertical. An off-centre load produces a twist that the upper and lower beams take up as equal and opposite horizontal forces through their pivots, and these have no turning effect on the balance. Only the vertical load affects the result.

Does a Roberval balance measure mass or weight?

It compares masses. Both pans experience the same gravity, so balance is reached when the masses are equal, and it would give the same result anywhere. A spring scale, by contrast, measures force and would read differently where gravity is weaker.

How do I check that the balance is accurate?

With both pans empty the pointer should rest at the centre. Then swap an object and its matching weights between the pans; if they still balance, the two sides are equivalent. Two identical known weights, one on each pan, should also balance exactly.

What weights are used with this balance?

Any set of known masses of suitable size, commonly iron or brass weights for general weighing. Their accuracy limits the result, so a set that is kept clean and handled carefully gives the most reliable comparisons.

Who was Roberval?

Gilles Personne de Roberval was a French mathematician who presented this parallelogram balance to the French Academy of Sciences in 1669. The design is still the basis of many counter scales and kitchen scales with pans on top.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)