Search

In Stock

Dewar Flask Calorimeter

Calorimètre à vase DEWAR Complet avec couvercle, agitateur et résistances immergeables, Features a double-walled, vacuum-evacuated borosilicate chamber with internal silvering to virtually eliminate thermal transfer via conduction, convection, and radiation.

Modular Analytical Interface Calorimètre double paroi: Pertes thermiques négligeables, Includes a high-density insulated lid equipped with standardized ports for motorized stirrers, immersion heaters, and precision digital temperature probes to ensure experimental repeatability.

$16.02

Quick Answer: A Dewar flask calorimeter is a calorimeter built around a vacuum-insulated, double-walled flask, the same design as a vacuum flask. Because the Dewar flask calorimeter loses heat far more slowly than an open vessel, it gives more reliable results for specific heat capacity, latent heat and the heat of chemical reactions.

How the Dewar Design Blocks Heat Flow

Heat escapes from a vessel by conduction, convection and radiation, and a Dewar flask tackles all three. The space between its two walls is evacuated, so there is almost no gas to conduct heat across or carry it by convection. The facing wall surfaces are usually silvered, so radiation is reflected back rather than absorbed. The only easy path left is through the neck and lid, which is why the opening is kept narrow and covered during measurements.

The result is a vessel whose contents change temperature only slowly when left alone. In calorimetry that matters, because every joule lost to the surroundings during an experiment is a joule missing from the energy balance.

Calibrating and Using the Calorimeter

Even a well-insulated flask absorbs some heat itself. Its heat capacity is found first, either by mixing known masses of hot and cold water in it or by supplying a measured amount of electrical energy through an immersion heater and recording the temperature rise. That value is then included in every later calculation.

With the heat capacity known, the calorimeter can be used for the heat of neutralisation of an acid and a base, the heat of solution of a salt, the specific heat capacity of a metal by the method of mixtures, or the specific latent heat of fusion of ice. Recording the temperature for several minutes before and after the event and extrapolating both lines to the moment of mixing corrects for the small heat exchange that remains.

Specifications

Product Calorimeter with a Dewar (vacuum-insulated) flask
Insulation principle Evacuated double wall, normally with silvered inner surfaces
Typical measurements Specific heat capacity, latent heat, heats of reaction and solution
Calibration Heat capacity found by electrical heating or by mixing water
Flask capacity, lid and stirrer details Confirm at enquiry

Measurements

  • Heat of neutralisation and heat of solution experiments
  • Specific latent heat of fusion of ice with small heat-loss corrections
  • Specific heat capacity of metals by the method of mixtures
  • Electrical calibration practicals that compare energy supplied with heat gained

Care & Handling

  • Never drop samples or stirrers into the flask; lower them gently, because a cracked inner wall can make the flask implode
  • Avoid pouring very hot liquid into a cold flask in one go; warm it gradually to reduce thermal stress
  • Rinse and dry the flask after reactions so residues do not remain on the glass
  • Store the flask upright in its housing, away from the bench edge

Why Choose LabEquip

Chemistry and physics departments choose a Dewar flask calorimeter when results from simple cups are too affected by heat loss, especially for reactions and latent heat work. It is often used with a calorimeter lid with stirrer and submersible resistors for electrical calibration; contact LabEquip for details.

Frequently Asked Questions

Why does a Dewar flask lose so little heat?

Its two glass walls are separated by a vacuum, which stops conduction and convection between them, and the facing surfaces are usually silvered to reflect radiation. Heat can escape mainly through the neck and lid.

Is a Dewar flask calorimeter better than a copper calorimeter?

For slow processes and reactions it usually loses less heat, giving smaller corrections. A copper calorimeter reaches thermal equilibrium faster and is sturdier, so the choice depends on the experiment.

How is the heat capacity of the calorimeter found?

By putting in a known amount of energy and measuring the temperature rise, either by mixing known masses of hot and cold water or by electrical heating with a measured voltage, current and time.

Can acids and bases be mixed in it?

Dilute solutions of the kind used for heat of neutralisation experiments suit a glass Dewar flask. Rinse it thoroughly afterwards and avoid substances that attack glass, such as hot concentrated alkalis or hydrofluoric acid.

Why is a cooling correction still needed?

No insulation is perfect, and some heat passes through the lid and neck during the measurement. Plotting temperature before and after the event and extrapolating to the moment of mixing compensates for that small loss.

What is the main safety risk with a Dewar flask?

A cracked or chipped flask can implode and scatter glass. Inspect it before use, lower samples in gently, and keep it in its protective housing.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)