Quick Answer: The Conical Flask is a flat-bottomed laboratory flask with sloping sides and a narrow cylindrical neck, also called an Erlenmeyer flask. In physics and chemistry practicals the conical flask holds and heats liquids, lets solutions be swirled without spilling, and takes a bung for gas and steam set-ups.
Why the Shape Works
The flat base stands securely on a bench, a tripod gauze or a hot plate, while the sloping sides keep the centre of gravity low. When the flask is swirled, liquid climbs the walls and falls back inwards instead of slopping out, which is why titrations are carried out in a flask of this shape rather than a beaker. The narrow neck slows evaporation and takes a rubber or cork bung, a cotton-wool plug or a loose cover.
Many flasks of this type carry approximate volume marks on the side. They are useful for judging how much liquid has been added but are not accurate enough for measuring; a measuring cylinder, pipette or burette does that job. The listing does not state the glass type or capacity, so whether the flask can be heated directly should be checked with LabEquip before ordering for heating work.
In the Physics Laboratory
Physics teachers use the flask as a convenient boiler and reservoir. Water boiled in it, with a one-holed bung and delivery tube fitted, supplies steam for latent heat experiments. A flask with a bung and a long glass tube makes a simple liquid thermometer for showing expansion on heating, and an inverted flask with a jet tube is used in fountain demonstrations of air pressure. It also holds liquids whose density, viscosity or refractive index is being measured.
Typical Uses
- Titration, where the flask is swirled as the reagent is added
- Heating and boiling water or solutions over a burner or on a hot plate
- Generating steam through a delivery tube for heat experiments
- Preparing and holding liquids for density, viscosity and optics practicals
- Collecting filtrate and mixing solutions
Specifications
| Item | Conical (Erlenmeyer) flask |
| Shape | Flat base, sloping sides, narrow cylindrical neck |
| Closure options | Rubber or cork bung, cotton-wool plug or foil cover |
| Graduations | Approximate volume marks only, where present; not for measuring |
| Glass type and capacity | Confirm at enquiry |
Care & Handling
- Never heat the flask while it is fully stoppered; expanding air or steam can force out the bung or burst the flask.
- Heat on a gauze or hot plate and raise the temperature gradually, especially if the glass type is unknown.
- Clean with a flask brush and warm detergent solution, rinse with tap water and finish with distilled water.
- Inspect the base for star cracks before heating, and discard any cracked flask.
Why Choose LabEquip
Laboratories reorder flasks of this kind constantly because they are used in almost every practical and are among the glassware most often broken. LabEquip lists this flask in Physics Equipments; an Erlenmeyer flask in the chemistry range is also available. Ask about capacities and heat-resistant glass via the LabEquip contact page.
Frequently Asked Questions
Is a conical flask the same as an Erlenmeyer flask?
Yes. Erlenmeyer flask is the name taken from the chemist Emil Erlenmeyer, who introduced the design, while conical flask simply describes its shape. Both names refer to the same flat-based vessel with a tapering body.
Why use this flask rather than a beaker for titration?
The sloping sides let the liquid be swirled vigorously to mix the reagents without splashing out, and the narrow neck keeps drops from the burette inside the flask. A beaker would need a stirrer and loses liquid more easily.
Can I measure volumes with the marks on the flask?
Only roughly. Flask graduations are an approximate guide and can be several percent out. For accurate volumes use a pipette, burette, volumetric flask or measuring cylinder.
Can the flask be heated on a hot plate?
Flat-bottomed flasks suit hot plates, provided the glass is heat-resistant. Borosilicate glass tolerates heating and moderate temperature changes, while soda-lime glass is more likely to crack, so check the glass type of this flask before using it for heating.
Why should the flask not be stoppered while heating?
Air and vapour inside expand as they warm. In a sealed flask the pressure rises until the stopper shoots out or the glass breaks. Fit a bung with a delivery tube or leave the neck open while heating.
How should I clean residues from the flask?
Rinse straight after use, then scrub with a flask brush that reaches the edges of the base, using warm water and laboratory detergent. Stubborn deposits may need a suitable dilute acid rinse; finish with distilled water and dry upside down on a rack.
Last Updated: October 2026










Reviews
There are no reviews yet.