Search

In Stock

Bernoulli Model

Maquette Bernoulli, Integrated Multi-Point Manometric Array enables precise Evaluation of static pressure drops across distinct longitudinal points, reinforcing the mathematical derivation of Bernoulli’s Equation.

High-Transmittance Acrylic Architecture supports visual Observation of fluid behavior and manometric equilibrium, essential for evidentiary-grade laboratory reporting and data synthesis.

$164.24

Quick Answer: The Bernoulli model is a fluids demonstration in which liquid flows along a channel that narrows and widens again, with the pressure read at several points along it. The Bernoulli model shows that pressure is lowest where the flow is fastest, as Bernoulli’s principle predicts.

Energy Bookkeeping Along the Flow

Bernoulli’s equation is an energy balance. For steady flow of an ideal fluid, p + ½ρv² + ρgz stays constant along a streamline: pressure energy, kinetic energy and potential energy per unit volume can trade with each other but their sum does not change. Dividing by ρg turns each term into a height, so the pressure head, the velocity head v²/2g and the elevation add up to a constant total head.

In a horizontal model the elevation term is the same everywhere, so any gain in velocity head must be paid for by a loss of pressure head. The continuity equation, A₁v₁ = A₂v₂, says where that happens: if the cross-section halves, the speed doubles and the velocity head becomes four times larger, so the pressure reading at the narrow section drops well below its neighbours.

Reading the Model Quantitatively

Measure the flow rate by collecting the outflow for a timed interval, then divide by the area of each section to find the local speed. Add the calculated velocity head to the measured pressure head at each tapping. The totals should be nearly equal, falling only slightly along the flow as friction converts a little mechanical energy into heat.

Plotting the results gives two lines along the model: the hydraulic grade line through the measured pressure heads, which dips at the narrow section, and the energy line above it, which stays almost level. Seeing those two lines side by side makes the trade between pressure and speed concrete. Section areas and tapping positions are confirmed at enquiry.

Demonstrations and Calculations

  • Showing pressure falling where the flow speeds up
  • Calculating velocity heads from measured flow rate and section area
  • Drawing the hydraulic grade line and the energy line
  • Explaining atomisers, carburettors and roofs lifted in high winds

Specifications

Product Bernoulli’s principle demonstration model
Usual layout Flow section that narrows and widens, with pressure-reading points
Principle p + ½ρv² + ρgz = constant along the flow, for an ideal fluid
Companion relation Continuity, A₁v₁ = A₂v₂
Section areas, tapping positions and water supply Confirm at enquiry

Care & Handling

  • Prime the model slowly so air is swept out of the pressure-reading tubes
  • Use clean water, with a little dye if the tubes are hard to read
  • Keep the flow steady while readings are taken
  • Drain, rinse and dry after use, and keep solvents off transparent plastic parts

Why Choose LabEquip

Teachers who want students to calculate with Bernoulli’s equation, not just observe it, need pressure readings at known sections, and the Bernoulli model provides them. For the meter form of the same idea see the Venturi tube, or compare our Bernoulli tube apparatus; contact LabEquip to confirm the layout, or browse physics lab equipment.

Frequently Asked Questions

What does each term in Bernoulli’s equation represent?

p is the pressure energy per unit volume, ½ρv² the kinetic energy per unit volume and ρgz the potential energy per unit volume. Along a steady streamline of an ideal fluid their sum stays constant.

How is the speed at the narrow section calculated?

Divide the measured flow rate by the cross-sectional area there. Halving the area doubles the speed, which makes the velocity head four times larger.

What is the difference between the hydraulic grade line and the energy line?

The hydraulic grade line joins the measured pressure heads. The energy line lies above it by the velocity head v²/2g at each point and, because of friction, slopes gently downward along the flow.

Why does the total head fall slightly along the model?

Real water has viscosity, so friction turns a little mechanical energy into heat as it flows. Bernoulli’s equation assumes an ideal fluid, and the small fall shows how far a real flow departs from it.

Where is Bernoulli’s principle seen outside the lab?

In perfume atomisers and paint sprayers, in the carburettors of older engines, and in roofs lifted when fast wind passes over them while the air inside the building is still.

Does the model need a pump?

How water is supplied, from a header tank, a tap or a small pump, can be confirmed at enquiry. What matters is a steady flow, so that the pressure readings settle before they are taken.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)