Quick Answer: An air track apparatus is a long, hollow, perforated track through which a blower forces air, so that gliders ride on a thin cushion of air with almost no friction. It is used in mechanics laboratories for experiments on uniform motion, Newton’s second law, collisions and conservation of momentum.
Removing Friction from the Experiment
Friction is the main reason that simple motion experiments disagree with theory: a trolley pushed along a bench slows down, and its losses are hard to measure. The air track removes most of that friction. Air from a blower enters the hollow track and escapes through rows of small holes along its upper faces, lifting each glider a fraction of a millimetre. The glider then moves with almost no contact, so a gentle push sends it the whole length of the track at nearly constant speed.
That behaviour is Newton’s first law made visible, and it is the starting point for the rest of the experiments. With friction out of the way, a small hanging mass pulling a glider produces an acceleration that matches the applied force divided by the total mass moved. Two gliders that collide show their total momentum before and after the collision agreeing closely, whether they bounce apart from spring bumpers or stick together.
Timing is done with stopwatches over marked distances, or with light gates and an electronic timer where the laboratory has them. Light gates measure the time a card of known length on the glider takes to pass, which gives the glider’s speed directly.
Specifications
| Type | Linear air track with perforated hollow track and gliders |
| Principle | Air cushion from a blower reduces friction between glider and track |
| Levelling | Adjustable feet or levelling screws |
| Timing | Stopwatch over marked distances, or light gates where available |
| Track length, gliders, blower and accessories | Confirm at enquiry |
Levelling and Setting Up
The track must be level before any measurement, otherwise gravity adds a hidden force. Switch on the blower, place a glider at rest in the middle, and adjust the levelling screws until it stays put without drifting either way. Check again at two or three positions along the track, since a slight sag shows up as gliders gathering at one point.
Experiments on the Air Track
- Showing uniform motion of a glider when no net force acts
- Verifying Newton’s second law with a hanging mass over a pulley
- Conservation of momentum in elastic and inelastic collisions
- Kinetic energy before and after collisions
- Motion down a gently inclined track, with the track tilted by a known height
Care & Handling
- Keep the track surface clean and free of dust, grit and fingerprints, which drag on the gliders.
- Never slide a glider along the track with the blower off; it scratches both surfaces.
- Store gliders separately so their undersides are not dented, and keep the air holes clear.
- Use the blower on a dry bench, keep its lead tidy, and switch it off at the socket after use.
Why Choose LabEquip
Colleges and senior schools buy the air track apparatus as a centrepiece of their mechanics lab equipment, usually with a digital stop watch or light gates for timing. LabEquip offers it in its physics lab equipment range, and the track length, gliders and blower can be agreed through our contact page.
Frequently Asked Questions
Why do gliders on an air track keep moving for so long?
Air escaping through the holes lifts the glider so it barely touches the track. With friction almost removed, there is very little force to slow it down, so it moves at nearly constant speed.
How do I level the track?
Switch on the blower, place a glider at rest at the centre and turn the levelling screws until the glider stays still. Repeat at other points along the track to check that it does not sag.
Can the air track show conservation of momentum?
Yes. Two gliders of measured mass are timed before and after a collision. The total momentum before and after agrees closely because external friction is so small.
What is the difference between an elastic and an inelastic collision on the track?
In an elastic collision the gliders bounce apart, for example from spring bumpers, and kinetic energy is nearly conserved. In an inelastic collision they stick together and some kinetic energy is lost, though momentum is still conserved.
Is a blower needed?
Yes, the air supply is what creates the cushion. A blower of suitable output is connected to the end of the track by a hose; the blower to be used should be agreed when ordering.
How is the speed of a glider measured?
Either by timing it over a marked distance with a stopwatch or by fitting a card of known length that interrupts a light gate. The card length divided by the interruption time gives the speed.
Last Updated: October 2026










Reviews
There are no reviews yet.