Search

In Stock

Specimen Mounting Press

Thermostatic Thermal Regulation: Equipped with a high-precision heating system and integrated cooling manifold, allowing for rapid curing cycles and precise temperature maintenance up to 200°C for both thermoplastic and thermosetting resins.

Hydraulic Force Calibration: Features a heavy-duty hydraulic ram with an integrated pressure gauge, capable of delivering up to 150 kg/cm² to ensure high-density, bubble-free specimen encapsulation for superior edge retention during preparation.

$99.83

Quick Answer: The Specimen Mounting Press is a metallography press that encapsulates a small or awkwardly shaped sample in a cylinder of mounting resin, using heat and pressure. A specimen mounting press produces mounts of uniform size that are easy to hold during grinding and polishing.

Why Samples Are Mounted

A fragment of wire, a thin sheet or a small fastener is almost impossible to hold flat against a grinding paper, and its edges round off during polishing. Mounting solves both problems. The sample is placed face down in the press cylinder, mounting powder is poured over it, and the resin is heated under pressure until it cures into a solid cylinder with the sample face exposed. The mount handles like a puck, fits sample holders and keeps edges sharp for examination.

Hot compression mounting with thermosetting resins such as phenolic types is the usual method for metals, because it is quick and gives hard, durable mounts. Materials that cannot tolerate the heat or pressure, such as some polymers or delicate coatings, are cold-mounted in casting resins instead. The listing does not state the mould diameter, heating arrangement or pressure system, so confirm these, with the resin type recommended, at enquiry.

Finished mounts go straight on to the belt grinder or to grinding papers. Label each one on the back by engraving or with a marker, because mounts of similar materials look alike once the resin has set.

Specifications

Item Press for hot mounting of specimens
Output Cylindrical resin mount with the specimen face exposed
Typical mounting materials Thermosetting powders such as phenolic resin
Purpose Easier grinding and polishing, edge retention, uniform size
Mould diameter, heating and pressure system Confirm at enquiry

Care & Handling

  • Clean resin residue from the specimen mounting press mould and ram after each cycle so later mounts eject freely.
  • Apply a release agent to the mould if the resin instructions recommend one.
  • Wear heat-resistant gloves when removing mounts, and cool the mould as the resin instructions direct before ejecting.
  • Keep mounting powders sealed and dry, as damp powder cures poorly.

Applications

  • Mounting small steel, copper or aluminium samples for microstructure practicals
  • Holding wires, sheet sections and fasteners upright for cross-section study
  • Protecting edges and coatings when examining case depth or plating
  • Producing uniform mounts for grinding and polishing holders

Why Choose LabEquip

Materials testing labs and engineering colleges with a metallography course buy mounting presses to make sample preparation consistent. The press is listed with cutting and grinding equipment in the Microscope & Optics range; send your sample sizes and mounting needs through the contact page.

Frequently Asked Questions

What is the difference between hot and cold mounting?

Hot mounting cures a thermosetting powder under heat and pressure in a press, giving hard mounts within minutes. Cold mounting uses liquid resins that cure at room temperature without pressure, which suits heat-sensitive or fragile samples but takes longer.

Why are my mounts cracked or cloudy?

Cracks often come from cooling too quickly or from a sample too large for the mould. Cloudy, soft or porous mounts usually mean the resin was not held at temperature and pressure long enough, or the powder was damp.

How much resin should I use?

Use enough to cover the sample well and give a mount tall enough to grip comfortably. Follow the resin supplier’s guidance for the mould size, and measure the powder each time so mounts come out at a consistent height.

Can a sample be removed from the mount afterwards?

Thermoset mounts are hard to remove and are usually kept as the permanent sample. If the specimen must be recovered later, cold mounting, or cutting through the mount, is the practical route.

Do I need to clean samples before mounting?

Yes. Remove oil, cutting fluid and loose burrs, and dry the sample. Contaminants stop the resin bonding to the sample, leaving a gap at the edge that traps polishing grit and liquids.

Can I mount several samples together?

Small samples can share a mount if they fit without touching and can be told apart, for example by arranging them in a known pattern. That saves time when comparing materials, but only if the arrangement is recorded.

Last Updated: September 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)