Search

In Stock

Tubes, Delivery

Geometric Versatility: Offered in precision-bent 90-degree, 180-degree, and straight profiles with fire-polished ends to ensure secure, leak-proof connections with rubber bungs or flexible tubing.

Thermal and Chemical Inertness: Manufactured from high-expansion-resistant glass to withstand corrosive chemical vapors and moderate temperature gradients without leaching or structural degradation during gas evolution.

$1.64

Quick Answer: A delivery tube is a length of glass tubing bent to shape, such as an L or U, that carries gas from a reaction vessel to where it is collected or tested. It passes through a hole in a rubber bung or cork on the generating flask or test tube.

Carrying Gas From Flask to Jar

Almost every gas preparation in school chemistry needs a delivery tube. Hydrogen from zinc and dilute acid, carbon dioxide from marble chips and hydrochloric acid, and oxygen from hydrogen peroxide with manganese(IV) oxide all leave the flask through a bent glass tube in its bung and travel to a gas jar over water, a syringe or a test tube of limewater. The bend and length decide whether the gas can reach under a beehive shelf in a trough, up into an inverted jar or down to the bottom of an upright one.

Glass tubes are clear, so a teacher can see liquid creeping back towards a hot flask, and they resist the acids, alkalis and gases met in school work. Common forms are the right-angle L tube, the U tube and tubes bent twice for upward or downward delivery.

The weak point is the joint with the bung. A common cause of cuts in school laboratories is pushing glass tubing through rubber, when a tube snaps and the broken end is driven into the hand. Wetting the tube with water or glycerol, holding it close to the bung and protecting the hand with a cloth prevent most of these injuries.

Care & Handling

  • Take the tube out of the water before you stop heating, or cold water will be sucked back into the hot vessel and crack it.
  • Lubricate with water or glycerol and twist gently when inserting into a bung; never force it.
  • Fire-polish or inspect cut ends, because a sharp end cuts both rubber and hands.
  • Rinse tubes after use so acid spray and limewater deposits do not dry inside.

Applications

  • Collecting gases over water in a trough with a beehive shelf
  • Bubbling carbon dioxide through limewater to identify it
  • Upward or downward delivery of gases that dissolve in water, such as ammonia or hydrogen chloride
  • Leading gases from heated solids, such as carbon dioxide from copper(II) carbonate, into test reagents

Specifications

Item Bent glass tubing for gas transfer
Shapes in use L (right-angle), U and double-bend forms
Connection Through a rubber bung or cork on the generating vessel
Gases handled Hydrogen, oxygen, carbon dioxide and other school preparation gases

Why Choose LabEquip

Schools buy delivery tubes in class quantities for gas-preparation practicals and replace them regularly as tubes break. LabEquip lists them in the chemistry lab equipment range, where they pair with vessels such as the flat bottom boiling flask; send the shapes and quantities needed through the contact page.

Related Products

Frequently Asked Questions

What causes suck-back through a delivery tube and how is it prevented?

If a heated flask cools while the delivery tube still dips under water, the drop in pressure pulls water back up the tube into the hot flask, which can crack it. Lift the delivery tube out of the water before removing the heat.

How is glass tubing pushed into a rubber bung safely?

Wet the glass and the hole with water or glycerol, wrap a cloth round the hand, hold the tube close to the bung and push with a twisting motion. Pushing a dry tube, or holding it far from the bung, is how tubes snap and cut hands.

Which delivery method suits which gas?

Gases that dissolve little in water, such as hydrogen and oxygen, are collected over water. Gases denser than air, such as carbon dioxide, can be collected by downward delivery into an upright jar, and lighter gases, such as ammonia, by upward delivery into an inverted jar.

Can glass delivery tubes be bent in the school laboratory?

Soda glass tubing can be bent by rotating it in a wide, fishtail flame until it softens, then bending it gently and letting it cool on a heat-proof mat. Fire-polish the cut ends so they are smooth before use.

Why use glass delivery tubes instead of rubber tubing?

Glass is clear, so liquid creeping back towards a hot flask can be seen, and it keeps its shape, which helps it reach under a jar or beehive shelf. Short pieces of rubber tubing are still used to join glass sections flexibly.

How far should the delivery tube go into the collecting jar?

For downward or upward delivery, the tube should reach almost to the far end of the jar, so the gas pushes the air out from the other end. Over water, the tube end only needs to sit under the jar mouth or the beehive shelf.

Last Updated: November 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)