Search

In Stock

Funnel Holder, Plastic

Corrosion-Resistant Polypropylene Architecture: Precision-molded from medical-grade polypropylene, ensuring total resistance to aggressive acids and alkalis while providing a non-sparking safety profile in volatile chemical environments.

Universal Tapered Clamping Interface: Features a specialized internal wedge design and a high-torque adjustment screw, facilitating a secure, vibration-free grip on support rods up to 12.5mm in diameter without marring surface coatings.

$3.38

Quick Answer: A plastic funnel holder is a ring on an arm that clamps to a laboratory stand rod and supports a funnel at a chosen height. The listing image shows a ring, a short arm and a knob-tightened clamp.

A Ring That Does Not Rust

Filtration needs the funnel held steady above the receiving vessel, with its stem touching the inner wall so the filtrate runs down without splashing. The traditional iron ring and boss rusts in the damp, acidic air of a chemistry lab, and hard metal against a glass funnel risks chipping it. A plastic holder does the same job without corrosion and is gentler on the glass.

Judging from the image, the holder slides onto a vertical stand rod through the opening at the end of the arm and is locked by turning the knob.

The holder suits long stem filter funnels for gravity filtration, and it can also cradle a separating funnel during an extraction if the ring size fits.

Applications

  • Gravity filtration of a precipitate into a beaker or conical flask
  • Holding a funnel above a burette or bottle for filling
  • Supporting a separating funnel during solvent extraction
  • Filtration set-ups in damp or corrosive areas where iron rings rust

Specifications

Item Funnel holder: ring on an arm with a stand-rod clamp
Mounting Clamps to a vertical stand rod; tightened by a knob
Supports Filter funnels, and separating funnels of suitable size
Material Plastic, as titled

Care & Handling

  • Tighten the knob only enough to hold; overtightening can crack a plastic clamp.
  • Position the funnel so its stem touches the inside wall of the receiver.
  • Rinse off acid splashes and dry the holder after use.

Why Choose LabEquip

Chemistry labs replacing rusting iron rings on their retort stands, and schools setting up many filtration stations at once, buy plastic funnel holders in sets. LabEquip lists them in its chemistry lab equipment range; share your stand rod diameter through the contact page.

Related Products

Frequently Asked Questions

How does a plastic funnel holder attach to a retort stand?

The holder is a ring on a short arm, and the end of the arm slides onto the vertical rod of a retort stand. Turning the knob, as shown in the listing image, locks it at the chosen height. Set the height so the funnel stem can reach just inside the receiving beaker or flask.

Why use a plastic funnel holder instead of an iron ring?

Iron rings rust in the damp, acidic air of a chemistry lab and leave stains on benches and stands, and hard metal against glass can chip a funnel. A plastic holder does not corrode and grips glass more gently, while doing the same job of holding the funnel steady during filtration.

Can a funnel holder support a separating funnel full of liquid?

It can cradle a small separating funnel if the ring is the right size, but a full funnel is heavy and is shaken and vented during extraction. For larger funnels use a dedicated separatory funnel holder or an iron ring with a clamp, and always keep a beaker underneath in case the stopcock leaks.

Where should the funnel stem sit during filtration?

Lower the holder until the tip of the funnel stem touches the inside wall of the receiving vessel. The filtrate then runs quietly down the glass instead of dripping and splashing, and with a long stem the unbroken liquid column speeds the filtration up.

How do I stop a filter funnel tipping in the holder?

Match the ring to the funnel: if the ring is too large the funnel sits low and leans, and if too small it perches high on the cone. Keep the retort stand base under the funnel, tighten the knob firmly and avoid filling the cone above the top of the filter paper.

Can a plastic funnel holder be used near a Bunsen burner?

Keep it away from flames and hot surfaces. Plastic softens with heat, and a holder clamped just above a burner or hot plate can distort and drop the funnel. For hot filtration over a heat source, use a metal ring on the stand and keep the plastic holder for cold gravity filtration.

Last Updated: November 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)