Quick Answer: An ammonia distillation apparatus is a glass set-up in which a sample is made alkaline and boiled so that ammonia is driven off, condensed and absorbed in a receiving acid. It is used to determine ammoniacal nitrogen in water and wastewater, and the nitrogen in Kjeldahl digests, by titration or colour measurement of the distillate.
Separating Ammonia Before Measuring It
Ammonia in a water or wastewater sample is often accompanied by colour, turbidity and dissolved substances that interfere with a direct test. Distillation separates it first. The sample is buffered or made alkaline, which converts ammonium ions to free ammonia, and on boiling the ammonia leaves with the steam. It condenses and is collected in a receiver holding boric acid solution or a measured volume of standard acid.
The distillate is then analysed. Ammonia trapped in boric acid is titrated with standard acid, while ammonia absorbed in a known excess of acid is found by back titration. Low concentrations are more often measured by a colour method, such as Nessler’s reagent compared in a Nessler cylinder, or the phenate method.
A splash head or trap bulb between the flask and condenser is usual in ammonia stills, so droplets of alkaline liquid cannot be carried into the receiver and give a falsely high result. For protein and organic nitrogen work built around a digestion flask, compare the Kjeldahl distillation assembly.
Applications
- Determining ammoniacal nitrogen in drinking water, river water and treated effluent
- Distilling Kjeldahl digests in soil, fertiliser and feed analysis
- Environmental science practicals on nitrogen pollution and water quality
- Checking ammonia in aquaculture water, where it is harmful to fish
Specifications
| Purpose | Separating ammonia from a sample by alkaline distillation |
| Receiving solution | Boric acid or a measured excess of standard acid |
| Finish | Titration, or colour methods for low concentrations |
| Typical parts | Distillation flask, splash head, condenser, delivery tube, receiver |
Care & Handling
- Before each run, steam out the apparatus with ammonia-free water to remove traces left on the glass by the previous sample.
- Keep the delivery tube tip below the surface of the receiving acid during distillation, and lower the receiver before heating stops so no suck-back occurs.
- Add alkali carefully down the side of the flask so it layers under the sample, and connect the apparatus before mixing.
- Rinse the condenser and delivery tube with a little distilled water into the receiver at the end, so no ammonia stays behind in the glass.
Why Choose LabEquip
Water testing, environmental and agricultural laboratories use an ammonia distillation apparatus whenever sample colour or turbidity would disturb a direct test. LabEquip carries it among its chemistry lab equipment; mention the method you follow and the parts required when you write via the contact page.
Related Products
- Kjeldahl Distillation Assembly: A Kjeldahl distillation assembly for distilling ammonia from acid-digested samples to find total nitrogen.
- Micro Kjeldahl Nitrogen Distillation Apparatus: A compact micro Kjeldahl steam-distillation unit for small aliquots containing milligram amounts of nitrogen.
- Cylinder, Nessler: A Nessler cylinder for visual colour comparison when the distilled ammonia is too dilute to titrate.
- Distillation Apparatus: A general distillation apparatus for other separations by boiling point in the same laboratory.
Frequently Asked Questions
How does an ammonia distillation apparatus work?
The sample goes into the distillation flask and is made alkaline, then boiled. Ammonia leaves with the steam, passes through a splash head and condenser, and is delivered into a receiver holding an absorbing acid. The ammonia trapped there is then measured, so the result gives the ammoniacal nitrogen in the original sample.
Why is the sample made alkaline before ammonia is distilled?
In neutral or acidic water, ammonia is present mostly as ammonium ions, which stay dissolved and do not distil. Adding a buffer or alkali raises the pH so that ammonium ions turn into free ammonia, which is volatile and comes off readily with the steam. Without that step most of the nitrogen would stay in the flask.
Why is boric acid used in the receiver for ammonia distillation?
Boric acid is a weak acid that holds ammonia as borate without needing to be measured exactly, because it is not itself titrated. After distillation the trapped ammonia is titrated directly with a standard strong acid, using a mixed indicator. The alternative is to collect into a measured excess of standard acid and back-titrate what is left.
How is the ammonia in the distillate measured?
For higher concentrations the distillate collected in boric acid is titrated with standard sulfuric or hydrochloric acid, and the volume used gives the amount of nitrogen. For low concentrations a colour method is used instead, such as Nessler’s reagent or the phenate method, comparing the colour of the distillate against standards.
How is suck-back prevented at the end of an ammonia distillation?
Keep the tip of the delivery tube just below the surface of the receiving acid while ammonia is collecting, then lower the receiver so the tip is out of the liquid before heating stops. As the flask cools, its pressure falls, and a tube still dipping into the acid would draw the receiver liquid back into the hot flask.
How is ammonia distillation related to the Kjeldahl method?
The Kjeldahl method first digests a sample in hot sulfuric acid, turning its organic nitrogen into ammonium sulfate. The second stage is the same alkaline distillation of ammonia into an absorbing acid, followed by titration. An ammonia distillation set therefore covers water and wastewater testing and the distillation step of Kjeldahl nitrogen analysis.
Last Updated: November 2026










Reviews
There are no reviews yet.