Search

In Stock

Water Bath for RE400 Evaporators

₹55,203.00

Quick Answer: The Water Bath for RE400 Evaporators is the heating bath of a rotary evaporator set: a round open bowl of heated water, pictured with a steel liner in a grey housing and a digital control panel, in which the evaporation flask turns while solvent is removed under reduced pressure.

The Bath’s Job in Rotary Evaporation

A rotary evaporator removes solvent by turning a round bottom flask under vacuum with its lower part sitting in warm water. Rotation spreads the liquid into a thin film over the inside wall, the vacuum lowers the solvent’s boiling point, and the bath replaces the heat carried off as the solvent evaporates. Without that heat the flask chills and evaporation slows almost to a stop.

RE400 in the title is the evaporator model the bath is matched to. A matched bath has the right height and bowl size to sit under the evaporator’s flask arm, so the flask can be lowered into the water at the correct angle. Fit to other evaporators depends on their lift range and flask size, which is worth checking before ordering.

A common starting point for the setting is the 20-degree rule: run the bath about 20 °C above the temperature at which the solvent boils under the chosen vacuum, and keep the condenser coolant about 20 °C below it. Evaporation stays brisk without bumping, and the condenser still traps the vapour.

Specifications

Type Heating bath for a rotary evaporator
Matched evaporator RE400, as titled
Form Round open bowl with a steel liner in a grey housing, as pictured
Control Digital display with push buttons, as pictured
Bath medium Water, as titled
Temperature range and bowl volume Confirm at enquiry

Where the RE400 Bath Is Used

  • Removing extraction solvents such as ethyl acetate or hexane after a work-up
  • Concentrating plant extracts in natural-product and pharmacognosy labs
  • Recovering solvent for reuse in teaching and research labs
  • Drying down samples before analysis or crystallisation

Care & Handling

  • Fill with distilled or deionised water to limit scale, deep enough to cover the lower part of the flask but not so full that it overflows when the flask goes in.
  • Lower the flask gradually and start rotation before heating a full flask, so heat reaches a moving film.
  • Empty, rinse and dry the bowl regularly; standing water grows algae and leaves deposits.
  • Check the bath’s rated maximum before using any liquid other than water.

Why Choose LabEquip

Chemistry departments, pharmacy colleges and extraction labs that already run an RE400 evaporator buy this bath as a matched replacement or second unit. LabEquip lists it in General Lab Products; send your evaporator details through the contact page.

Frequently Asked Questions

What temperature should the bath be set to?

Start about 20 °C above the boiling point of the solvent at the vacuum used, with the condenser about 20 °C below it. A solvent boiling at 40 °C under the chosen vacuum, for example, is usually run with the bath near 60 °C.

Why does the flask need to rotate in the bath?

Rotation spreads the liquid into a thin film that evaporates quickly and bumps less. It also mixes the flask contents, so heat from the bath reaches all of the liquid.

Can this bath be used with other evaporators?

It is matched to the RE400. Another evaporator may work if its flask sits at the right height and angle over the bowl, so compare its lift range and flask size first.

Should the bath contain water or oil?

The title gives water, which suits most solvent removal. Oil is only for higher temperatures and only in baths rated for it, because hot oil is a fire and burn risk.

Why is evaporation slow even though the bath is hot?

Check the vacuum first. A leak or weak pump raises the solvent’s boiling point, so the bath cannot drive evaporation. Also make sure enough of the flask is immersed and that condenser coolant is flowing.

How often should the bath water be changed?

Replace it whenever it turns cloudy or shows growth, and at least weekly in regular use. Distilled water and emptying the bath before long breaks keep the bowl free of scale.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)