Search

In Stock

Support stand for stainless steel bain-marie

₹689.00

Quick Answer: The Support stand for stainless steel bain-marie is a rectangular stainless steel wire frame with a hooked tab at each corner, as pictured, that hangs from the rim of a bain-marie tank so a tube rack or basket can sit in the water at a fixed height.

A Frame That Hangs on the Tank Rim

Despite the word stand, the photo shows no legs. The item is a single rectangle of round stainless steel rod with a short flat tab bent up and outward at each corner. Those tabs rest on the top edge of the tank, so the frame hangs inside it just below the rim, and a rack, basket or tray placed on the frame is held off the floor at a steady height. The image file calls it a support for a rack, which matches that shape.

Hanging a rack from the rim has practical advantages in a bain-marie. The rack’s height no longer depends on the tank floor, which in many small baths is the heated surface, and water circulates freely underneath. Lifting the frame by its corners brings the whole load up at once, useful when a set of tubes must leave the water together at the end of a timed step.

The frame’s outer size has to match the tank opening: too small and the tabs miss the rim, too large and it will not drop in. A wire test tube rack for water baths or a stainless steel rack for 16 tubes are the kinds of racks it carries.

How the Frame Is Used

  • Suspending a tube rack at a fixed depth for incubations at 37 °C or other set temperatures
  • Holding a basket of bottles clear of the heated floor while media or reagents warm
  • Lifting a full set of samples out of the bath in one movement at the end of a timed step
  • Giving a plain bain-marie a raised working level without extra legs on the floor

Specifications

Material Stainless steel round rod, as pictured
Form Open rectangular frame with a hooked tab at each corner
Position Hangs from the tank rim inside a bain-marie
Carries A tube rack, basket or tray
Legs None pictured; the rim takes the weight
Frame size and tank match Confirm at enquiry

Care & Handling

  • Load the rack evenly so the frame hangs level and no corner tab lifts off the rim.
  • Lift the frame by two opposite corners with heat-resistant gloves when the water is hot.
  • Rinse and dry after use, and check the corner tabs for bending, which can let the frame slip.

Why Choose LabEquip

Microbiology rooms and teaching labs with a stainless steel bain-marie buy this frame to hang their existing racks at working depth. LabEquip lists it in General Lab Products; send the tank’s opening size through the contact page.

Frequently Asked Questions

Why is it called a support stand if it has no legs?

The name describes its job of supporting a rack. In the photo it is a frame that hangs from the tank rim by its corner tabs, so the rim takes the weight instead of legs on the floor.

What does the frame hold?

It carries a tube rack, wire basket or small tray inside the bath. The load rests on the frame’s rods, clear of the tank floor.

How deep will the rack sit in the water?

That depends on how far the rack itself extends below the frame. Fill the bath so the water covers the liquid in the tubes while the tube tops stay above the surface.

Can the frame stay in the bath at high temperature?

Stainless steel rod is unaffected by hot water, so the frame can stay in place during heating. It gets hot too, so handle it with gloves.

Will it fit a bath of a different make?

Only if the tank opening has the same inside length and width, so that all four tabs rest on the rim. Measure the opening before choosing.

Why hang a rack instead of standing it on the floor?

The floor of a small bain-marie is often the heated surface. Hanging the rack keeps samples off it, lets water flow underneath and makes the whole load easy to lift out at once.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)