Search

In Stock

Rope for vibrator from Melde

Corde pour vibreur de Melde, High-Contrast Braided Surface Enables precise visual Analysis and identification of nodes and antinodes during stationary wave formation in varied lighting environments.

Low-Hysteresis Synthetic Fibers support the Evaluation of frequency response and tension variables without material-induced data drift, ensuring evidentiary-grade laboratory results.

₹210.00

Quick Answer: This is a string for Melde’s vibrator: the length of thread tied to the vibrating arm at one end and led over a pulley to a hanging mass at the other, so that standing waves can be set up along it. It is a consumable that physics labs replace when it stretches, frays or loses its knot.

Rigging the String Correctly

Tie one end of the string to the vibrator’s hook or eyelet with a knot that cannot slip, lead it horizontally to a smooth pulley clamped at the bench edge, and hang a mass hanger from the free end. The vibrating length runs from the attachment point to the top of the pulley, where the string leaves contact. Both ends then behave as nodes, and a standing wave forms when a whole number of half wavelengths fits between them.

Alignment matters more than students expect. The string should leave the vibrator along the line of the pulley groove; a string that runs at an angle rubs on the groove, alters the effective tension and makes the loops lopsided. Clamp both at the same height before loading.

Experiments That Use the String

  • Finding the frequency of the vibrator from the loop count, vibrating length, load and mass per metre
  • Showing that the square of the loop count varies inversely with the hanging mass
  • Comparing loop patterns when the vibrator moves along the string and when it moves across it

Choosing and Preparing a String

A good string for this experiment is flexible, barely stretches under the load, and has the same thickness all along. Stiff wire resists bending and shifts the nodes, while very stretchy thread changes its own mass per metre as the load rises. Weigh a long, measured piece before class and tag the coil with its mass per metre so every group uses the same value.

With the frequency held fixed, the number of loops depends on the tension: halving the number of loops needs four times the hanging mass. That square-law link is the most useful check that the string is behaving well, because a worn or uneven string gives loop counts that do not follow it.

Specifications

Item String (cord) for use with a Melde’s vibrator
Role Carries the standing wave between the vibrator and the pulley
Properties that matter Flexible, low stretch, uniform along its length
Used with Melde’s vibrator, bench pulley, mass hanger and slotted masses
Material, length and mass per metre Confirm at enquiry

Care & Handling

  • Cut a fresh length when the string frays near the knot, where it bends most
  • Unload the hanger at the end of a session so the string does not creep under constant tension
  • Keep the coil dry and free of oil, which adds mass and changes the readings
  • Weigh a new sample whenever a fresh coil is opened, rather than reusing an old value

Why Choose LabEquip

Labs that run Melde’s experiment every year keep spare string so each group starts with a fresh, uniform length. LabEquip lists this string alongside a membrane Melde’s vibrator and a separately listed Melde vibrator cord, within its physics lab equipment range. Ask which one suits your vibrator through LabEquip contact.

Frequently Asked Questions

How do I find the mass per metre of the string?

Weigh a long, measured piece on a sensitive balance and divide the mass by the length. A long piece keeps the percentage error small.

Why are there more loops when the hanging mass is reduced?

Lower tension makes the wave travel more slowly, so at the fixed vibrator frequency its wavelength is shorter. More half wavelengths then fit between the vibrator and the pulley.

Can I use sewing thread instead?

Cotton or polyester thread can work for a demonstration if it is uniform and stretches little. For quantitative work, use one consistent string and measure its mass per metre, since thread varies from reel to reel.

Why do the loops look uneven?

Uneven loops usually come from a string running at an angle to the pulley groove, a sticking pulley, or a string whose thickness varies. Realign the vibrator and pulley and replace a worn string.

What happens if the vibrator moves along the string instead of across it?

With the vibrator moving along the string, the string is tugged once per vibrator cycle but swings once every two cycles, so it vibrates at half the vibrator frequency and shows fewer loops for the same tension.

Is this string the same as the separately listed Melde cord?

Both listings are strings for the same experiment, and neither states a material or mass per metre. If you need to match an existing set-up, tell us your vibrator and pulley and we will compare the two before you order.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)