Search

In Stock

Adapter For Coaxial Cable

Adaptateur pour câble coaxial Engineered for standardized 50 Ohm or 75 Ohm environments to minimize signal reflection and Voltage Standing Wave Ratio (VSWR) during high-frequency data acquisition.

Gold-Plated Dielectric Interface Features high-conductivity contact surfaces and PTFE (Teflon) insulation to ensure low insertion loss and high mechanical durability across thousands of mating cycles.

₹1,650.00

Quick Answer: The Adapter for Coaxial Cable is a small housing on a stand that joins a coaxial cable connector to a pair of terminal sockets for ordinary laboratory leads. This coaxial cable adapter lets a signal generator or oscilloscope with coaxial sockets be connected to circuit boards, modules and transmission experiments on the bench.

Why Coaxial Cable Carries Signals

A coaxial cable has a central conductor, a surrounding insulating layer, a braided or foil screen and an outer sheath. The signal travels between the centre conductor and the screen, and the screen keeps outside electrical noise from reaching the signal and stops the signal radiating into neighbouring wires. That is why generators and oscilloscopes use coaxial connections.

Most bench circuits, however, are wired with single laboratory leads and terminal sockets. The coaxial cable adapter bridges the two systems in one tidy step instead of a tangle of improvised clips.

Keeping the Common Side Right

The product photograph shows a grey housing on a tilting stand, with a coaxial socket on one side and red and black terminal sockets on the front. In coaxial practice the screen is the common or ground side, so it normally corresponds to the black socket and the centre conductor to the red one.

Remember that the outer conductor of an oscilloscope input is usually connected to earth through the instrument. Connecting the black side of the adapter to any point in a circuit therefore joins that point to earth, which can short part of a circuit if it is placed carelessly.

Applications

  • Connecting a signal generator output to a circuit board with ordinary leads
  • Feeding a bench signal into an oscilloscope channel
  • Linking modulator and demodulator modules to coaxial instruments
  • Transmission-line demonstrations that use coaxial cable

Specifications

Product Adapter for coaxial cable
Connections Coaxial socket; red and black terminal sockets
Housing Small case on a tilting stand
Use Linking coaxial instruments to bench circuits
Coaxial connector type Confirm at enquiry

Care & Handling

  • Pull on the connector body, never on the cable, when disconnecting
  • Keep the coaxial socket free of dust and do not force a mismatched plug into it
  • Check continuity from screen to black socket before first use
  • Stand the adapter on the bench rather than letting it hang from its leads

Why Choose LabEquip

Physics and electronics laboratories buy a few of these adapters for every oscilloscope and generator, because they save time and reduce wiring mistakes in signal experiments. LabEquip supplies them with the modulator demodulator unit among its physics equipment; connector questions can go to the contact page.

Frequently Asked Questions

Which socket connects to the screen of the coaxial cable?

In normal practice the screen is the common side and corresponds to the black socket, with the centre conductor on the red socket. A quick continuity check with a multimeter confirms this before first use.

Why not use two ordinary leads for signals?

Unscreened leads pick up interference from mains wiring and nearby equipment, and at higher frequencies they also radiate and couple into each other. A coaxial cable keeps the signal screened over most of its length.

Does the adapter change the signal?

It is a passive connection and has no noticeable effect at audio and low radio frequencies. At very high frequencies the unscreened leads after the adapter matter more, so keep them short.

Why does connecting the black socket sometimes upset a circuit?

The screen of an oscilloscope input is usually earthed. Connecting the black socket to a point in a circuit joins that point to earth, which can short out part of the circuit if it is not already at earth potential.

What is the stand for?

The stand holds the adapter upright on the bench and takes the weight of the cable and leads off the sockets. That reduces strain on the connections and keeps the leads tidy.

How should the coaxial connector be looked after?

Push the plug straight in and lock it gently, release it by the connector body rather than the cable, and keep the socket clean. A loose or dirty coaxial connection causes noisy, unstable signals.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)