Quick Answer: The Elevator Motor is a geared electric motor with a winding drum and cord, built to raise a hanging mass the way a goods lift or hoist does. Physics and technology classes use the elevator motor to measure the work done lifting a load, the power delivered and the efficiency of the electrical-to-mechanical conversion.
Inside a Lifting Motor: Gearing and the Drum
A small electric motor spins fast but gives little torque, which is the opposite of what a lift needs. The elevator motor therefore passes its shaft through a gearbox that cuts the speed and multiplies the torque before it reaches the drum. The drum then turns rotation into a straight lift: the cord winds on at a speed equal to the drum’s angular speed times its radius, and the force on the cord equals the drum torque divided by that radius.
In the product photograph the motor housing carries terminal sockets, a mounting clamp and a drum with a cord and hook, so it can be fixed to the edge of a bench with the load hanging clear of the floor.
Measuring Work, Power and Efficiency
A typical run raises a known mass through a measured height while a stopwatch records the time. The useful work is m × g × h and the useful power is that work divided by the time. Meanwhile a voltmeter and ammeter, or a joulemeter, record the electrical input. The ratio of the two is the efficiency of the motor at that load.
Repeating the run with different masses shows that efficiency is poor with a very light load, when friction and gearbox losses dominate, and improves as the load grows towards the motor’s comfortable working range.
Experiments With the Elevator Motor
- Calculating the useful power when raising masses of different sizes
- Finding the efficiency of an electric lift and how it changes with load
- Relating motor current to the torque needed for heavier loads
- Timing the lift at different supply voltages to compare lifting speeds
Specifications
| Device | Geared lifting (hoist) motor |
| Output | Winding drum with cord and hook |
| Connection | Terminal sockets on the housing |
| Mounting | Clamp for fixing to a bench edge |
| Quantities studied | Work, power, efficiency, current against load |
Care & Handling
- Start with a light mass and add load in small steps, watching the current
- Keep feet and hands out from under the hanging load at all times
- Check the cord for fraying and the hook for opening before each class
- Use only the supply type and voltage marked on the motor
Why Choose LabEquip
This hoist motor links the electrical meters on a bench to the pulleys, masses and other mechanics lab equipment a school already owns, which is why physics and design-and-technology departments buy it together. LabEquip supplies it with the energy and efficiency models among its physics equipment; questions on loads and mounting can go through the contact page.
Frequently Asked Questions
How much mass can this lifting motor raise?
The safe load depends on the motor rating and the strength of the cord and hook, which should be confirmed at enquiry. In class, start with a light mass and increase it in small steps while watching the current.
Why does the current rise when a heavier mass is lifted?
A heavier load needs more torque at the drum. In the permanent-magnet DC motors commonly used in lifting models, torque is roughly proportional to current, so the motor draws more current to hold and raise the extra weight.
How is the lifting power calculated?
Multiply the mass in kilograms by g, about 9.8 newtons per kilogram, and by the height raised in metres to get the work in joules, then divide by the time in seconds. The answer is the useful power in watts.
Why is the efficiency poor with a very light load?
Friction in the gearbox and bearings and losses in the windings take roughly the same energy whatever the load. With a tiny load the useful work is small compared with these fixed losses, so the ratio is low.
Can the motor lower the load as well as raise it?
With a DC motor, reversing the supply polarity reverses the drum, so the load can be lowered under power. Lower it slowly and keep hands clear, because a falling mass can drive the motor faster than intended.
What else is needed for an efficiency experiment?
A suitable power supply, an ammeter and voltmeter or a joulemeter, a stopwatch, a metre rule, a mass hanger with slotted masses, and a clamp or stand to hold the motor at a bench edge.
Last Updated: October 2026










Reviews
There are no reviews yet.