Quick Answer: A long stem plastic funnel is a moulded plastic funnel with an extended outlet tube that reaches down into narrow-necked flasks, bottles and burettes. It is used for transferring liquids and solutions without spills and for gravity filtration where the filtrate must go straight into a narrow vessel.
Reaching Past the Neck
When liquid is poured into a volumetric flask or a reagent bottle through a short funnel, it can run down the outside of the neck or splash off the shoulder. A long outlet delivers it well inside the vessel, below the neck, so every drop reaches the contents. That matters in quantitative work, where losing a few drops of a solution being made up to volume introduces an error, and in stores, where drips down a bottle leave residues on the label and the shelf.
Plastic makes the funnel light and hard to break, which helps when it is used repeatedly for refilling bottles or by younger students. Polypropylene and polyethylene are the usual materials; both cope with dilute acids, alkalis and salt solutions in the cold, yet they soften with heat and some solvents make them swell.
A stem pushed tightly into a closed vessel’s neck can seal it, and trapped air then stops the flow, so lift the funnel slightly while pouring. For filtration with folded paper, the plastic analytical funnel is designed specifically for that job, and glass users can compare the long stem 60 degree funnel.
Applications
- Filling volumetric flasks when making up standard solutions, rinsing the funnel into the flask afterwards
- Filling burettes safely below eye level, with the funnel removed before the reading is taken
- Decanting reagents from stock bottles into smaller dropping or reagent bottles
- Adding liquids to a flask through a narrow neck during a reaction set-up
Care & Handling
- Lift or wedge the funnel slightly while pouring so air can escape from the vessel.
- Take the funnel out of a burette before reading or titrating, since a drip from it changes the volume.
- Keep separate funnels for acids, alkalis and organic liquids, marked on the rim, to avoid cross-contamination.
- Wash with warm detergent solution and a narrow bottle brush for the stem, then rinse with distilled water.
Specifications
| Item | Funnel with an extended outlet stem |
| Main use | Transferring liquids into narrow-necked vessels |
| Also used for | Gravity filtration into flasks and bottles |
Why Choose LabEquip
Laboratories that make up many solutions and refill reagent bottles use a long stem plastic funnel every day, and schools value its resistance to breakage. LabEquip lists it with the chemistry lab equipment; send diameters and quantities via the contact page.
Related Products
- Funnel, Plain 60 Degrees, Long Stem: A glass long stem filter funnel for solvents and warm liquids that a plastic funnel should not handle.
- Industrial Funnels, Plastic: A large industrial plastic funnel with handle for bulk transfers into carboys and drums.
- Powder Funnel, Plastic: A plastic powder funnel with a wide stem for pouring solids instead of liquids into narrow necks.
- Volumetric Flask: A volumetric flask, a narrow-necked vessel the long stem can fill below the neck without losing drops.
Frequently Asked Questions
What is a long stem plastic funnel used for?
It is used to transfer liquids into narrow-necked flasks, bottles and burettes without spills, because the extended outlet delivers the liquid well below the neck. It also works for gravity filtration when the filtrate has to run straight into a narrow vessel, and it does not break if dropped.
Why does liquid stop flowing through a funnel into a bottle?
If the funnel stem fits tightly in the bottle neck, air trapped in the bottle cannot escape, and the liquid stops. Lift the funnel slightly, or slip a bent paper strip or a short glass rod between stem and neck, so air can get out as liquid goes in.
Can a plastic funnel be used to fill a burette?
Yes, a small funnel makes filling a burette easier and cleaner. Fill with the burette below eye level, then remove the funnel before taking the starting reading, because drops left in the funnel can fall in later and change the volume. Rinse the funnel with the titrant first.
Which liquids should not be poured through a plastic funnel?
Polypropylene and polyethylene cope with water, dilute acids, alkalis and salt solutions in the cold, but some organic solvents soften or swell them, and hot liquids can distort them. Use a glass funnel for solvents, hot solutions and strong oxidising acids.
Can a long stem plastic funnel be used with filter paper?
Yes, a folded filter paper cone can sit in it for gravity filtration of cool aqueous mixtures, and the long stem then carries the filtrate deep into the receiving vessel. Check that the cone angle suits the folded paper; if the paper does not lie flat against the wall, filtration will be slow.
How do I clean the long stem of a plastic funnel?
Rinse it immediately after use, then wash in warm detergent water with a long thin brush through the stem and rinse with distilled water. Avoid abrasive pads and solvents that could cloud or soften the plastic, and dry it hanging so water does not stay in the stem.
Last Updated: November 2026










Reviews
There are no reviews yet.