Quick Answer: A physical balance is a double-pan, equal-arm beam balance used in school and college physics laboratories to measure mass by comparison with standard weights. It is the classic instrument for practicals on mass, density and the sensitivity of a balance.
Parts of the Physical Balance
A vertical pillar on a levelling base carries a beam that rests on a central knife-edge. Two stirrups hang from knife-edges at the ends of the beam, each supporting a pan, and the two arms are made as nearly equal as possible. A pointer attached to the beam swings over a scale near the foot of the pillar, and small balancing nuts at the beam ends let the empty instrument be set to read zero.
Turning the release knob lowers the beam onto its knife-edges for weighing; turning it back raises the beam and pans onto rests. A plumb line or bubble level, with the levelling screws, makes the pillar vertical before every session. Students record the turning points of the pointer rather than waiting for it to stop, because a sensitive beam swings for a long time.
The Method of Oscillations
With the pans empty, the beam is released and five consecutive turning points are read, three on one side and two on the other. The mean of each side is found and the two means averaged to give the zero rest point. The same is done with the body and weights loaded, adjusting the weights until the loaded rest point falls just either side of the zero; interpolating between the two gives the mass to a fraction of the smallest weight used.
Sensitivity is the shift of the rest point caused by a small extra mass, expressed in scale divisions per milligram. Double weighing removes the error of unequal arms: weigh the body on the left pan, then on the right, and take the square root of the product of the two results.
Practicals and Experiments
- Determining the mass of a solid by the method of oscillations
- Finding the sensitivity of the balance for different loads
- Measuring density and relative density, including liquids in a specific gravity bottle
- Verifying Archimedes’ principle by weighing a body in air and in water
- Gauss’s double weighing to find the true mass when the arms are slightly unequal
Specifications
| Pattern | Double pan, equal-arm beam balance |
| Bearings | Knife-edges on flat bearing surfaces |
| Indicator | Pointer moving over a scale at the pillar foot |
| Controls | Beam release knob, levelling screws, balancing nuts |
| Mass measured by | Comparison with a separate set of weights |
| Capacity, sensitivity and case | Confirm at enquiry |
Care & Handling
- Lower the beam onto its rests before putting anything on or taking anything off the pans.
- Close the case doors, where fitted, while reading so that draughts do not move the pointer.
- Never exceed the rated load; the knife-edges are the most delicate part of the instrument.
- Keep the weights in their box and lift them with forceps to keep them free of grease and moisture.
Why Choose LabEquip
Physics departments preparing senior secondary and first-year college practicals usually order physical balances with a matching physical weights set. LabEquip lists this balance among its physics lab equipment, so balances and weights can be quoted together through LabEquip’s contact form.
Frequently Asked Questions
What is the method of oscillations?
It is a way of finding the rest point of the pointer from its swings instead of waiting for it to stop. Read an odd number of successive turning points, average those on each side separately, then take the mean of the two averages.
How does double weighing correct for unequal arms?
If the arms differ slightly, a body appears heavier on one pan and lighter on the other. Weighing it on both pans and taking the square root of the product of the two readings cancels the arm ratio and gives the true mass.
What does the sensitivity of the balance mean?
Sensitivity is how far the rest point moves for a small added mass. A more sensitive instrument shows a larger deflection, so smaller differences in mass can be detected. It usually falls slightly as the load increases.
Can a physical balance be used to weigh a body in water?
Yes. A small bridge is set over one pan so that a beaker of water stands on it without touching the pan, and the body hangs by a thread from the hook above that pan. The apparent loss of weight in water gives the body’s volume and hence its density.
Why does the balance have a plumb line or level?
The knife-edges work correctly only when the pillar is vertical. A tilted base shifts the zero and can make the pointer rub. Adjust the levelling screws until the plumb bob hangs over its mark or the bubble is centred.
Which weights are used with a physical balance?
A boxed set of standard masses down to milligram fractions, handled with forceps, is the usual companion. The set should cover the capacity of the balance and include fractions fine enough for the experiment.
Last Updated: October 2026










Reviews
There are no reviews yet.