Quick Answer: A simple distillation assembly is a basic glass set-up of a boiling flask, a single condenser and a receiver, with a thermometer to record vapour temperature. It separates a liquid from dissolved solids, or two liquids whose boiling points are far apart, and is the first distillation technique most students learn.
When a Simple Set-Up Is Enough
Simple distillation relies on a single evaporation and condensation. That is sufficient when only one component evaporates readily, as when water is recovered from seawater or copper(II) sulfate solution, or when two liquids differ in boiling point by a wide margin; a gap of roughly 25 °C or more is the figure commonly quoted in textbooks. Closer boiling points call for a fractionating column between flask and condenser.
The simple type assembly keeps the number of parts small, which makes it quicker for students to set up correctly and easier for a teacher to check at a glance.
Distilling a sodium chloride solution makes a good check on technique: the distillate should give no white precipitate with acidified silver nitrate, showing that no salt solution splashed over. For a general-purpose set see the distillation apparatus listing, and for separating oils from plant material the steam distillation assembly.
Applications
- Obtaining pure water from salty or coloured water in lower secondary practicals
- Separating ethanol from water to introduce the idea of boiling point differences
- Purifying a crude liquid product after an organic preparation
- Practical skills assessments in which students assemble and label the apparatus
Care & Handling
- Put anti-bumping granules in before heating to prevent sudden violent boiling.
- If the set uses ground joints, grease them very lightly or fit PTFE sleeves so they separate easily after heating.
- Keep the collected distillate away from the heat source, especially when it is flammable.
- Let the whole assembly cool before dismantling it, then rinse each part promptly.
Specifications
| Type | Simple distillation: one evaporation and one condensation |
| Suited to | Liquid from dissolved solid; liquids with widely separated boiling points |
| Main parts | Boiling flask, thermometer, condenser, receiver |
| Not suited to | Mixtures with close boiling points, which need a fractionating column |
Why Choose LabEquip
Schools and junior colleges choose a simple distillation assembly when every student group needs to carry out the technique itself. LabEquip supplies these within its chemistry lab equipment; send the number of sets required through the contact page.
Related Products
- Distillation Apparatus: A general distillation apparatus of flask, still head or side arm, thermometer, condenser and receiver.
- Distillation Assembly, Steam: A steam distillation assembly for extracting oils that would decompose at their own boiling points.
- Flask, Distillation: A distillation flask with a side arm, the boiling vessel for a simple bung-jointed set-up.
- Reflux Assembly: A reflux assembly for heating a reaction mixture at its boiling point before the product is distilled.
- Condenser, Liebig (Sampling): A Liebig condenser that slopes down from the flask to cool the vapour back to liquid.
Frequently Asked Questions
What can a simple distillation assembly separate?
A simple distillation assembly separates a liquid from a dissolved solid, such as water from salt water or copper(II) sulfate solution, and two liquids whose boiling points are far apart. A gap of about 25 °C or more is the figure usually quoted in textbooks. Mixtures with closer boiling points need a fractionating column.
Why can simple distillation not fully separate ethanol and water?
Their boiling points, about 78 °C and 100 °C, are too close for a single evaporation and condensation, so the vapour always carries both. The first distillate is richer in ethanol, but water comes over with it. Even fractional distillation stops at an azeotrope of roughly 95 percent ethanol, which boils as if it were a single substance.
What do anti-bumping granules do in a distillation flask?
They are small porous pieces of pumice or ceramic that release tiny bubbles and give the liquid places to start boiling evenly. Without them, a liquid can overheat and then boil in sudden violent bursts, known as bumping, that can throw liquid into the condenser. Add fresh granules to cold liquid before heating, never to hot liquid.
How do students know when to stop collecting the distillate?
Watch the thermometer at the side arm. While a pure substance distils, the temperature stays steady at its boiling point. When that component has nearly all distilled, the temperature drops or starts rising towards the next boiling point; that is the moment to stop heating or to change the receiver for the next fraction.
How is pure water obtained from salt water by simple distillation?
Heat salt water in the flask until it boils. The water vapour passes into the condenser, where it cools and drips into the receiver as pure water, while the salt, which does not evaporate, stays behind. Students can test the distillate by evaporating a drop on a watch glass and checking that no solid remains.
Is a Bunsen burner safe for heating a simple distillation?
For aqueous mixtures such as salt water or ink, a Bunsen burner with a tripod and gauze is acceptable with steady, moderate heat. For flammable liquids such as ethanol, use a water bath or heating mantle instead, because escaping vapour can catch fire at an open flame. Keep the flame away from the receiver at all times.
Last Updated: November 2026










Reviews
There are no reviews yet.