Quick Answer: A long plain bend receiver adapter is a curved glass distillation fitting without a side tube, made with an extended delivery limb. The extra length carries distillate further down into the receiving vessel, for example into a narrow flask, a cooled receiver or below the surface of an absorbing solution.
What the Extra Length Is For
The standard plain bend releases distillate just inside the mouth of the receiver. The long version reaches well inside, which helps in three situations. With volatile distillates, delivering low in a cooled receiver reduces the vapour lost from the neck. With tall or narrow receivers such as a measuring cylinder, the tip passes the neck so drops fall freely instead of running down the inner wall. And when the product is a volatile base such as ammonia, the long limb can dip under a trapping solution of acid so nothing escapes to the air.
That last use needs attention. A tip below a liquid surface can suck the liquid back into the condenser when heating is reduced or stops, so lower the receiver until the tip is just clear of the solution before switching off the heat.
The title gives no length, joint size or bend angle, and long is relative to the matching short pattern rather than a fixed dimension.
Specifications
| Type | Receiver adapter, plain bend, long pattern |
| Delivery limb | Extended compared with the standard bend |
| Side tube | None |
| Typical receivers | Tall, narrow or cooled flasks; absorbing solutions |
Applications
- Collecting ammonia in standard acid during nitrogen determinations, with the tip under the absorbing solution
- Delivering volatile solvents deep into an ice-cooled receiver
- Filling a tall measuring cylinder directly in experiments that record distillate volume
- Steam distillation into a flask where splashing at the neck must be avoided
Care & Handling
- The long limb is the most exposed part, so store the adapter lying in a padded tray or hung by its joint, never standing on the tip.
- Brush out the full length of the limb, as residue gathers at the lowest point of the curve.
- Whenever the tip is under liquid, keep an eye on the receiver as the heating is turned down.
Why Choose LabEquip
Food, agricultural and pharmacy testing labs that distil ammonia or other volatile components into trapping solutions often prefer the long bend. LabEquip offers it alongside the Kjeldahl distillation assembly and other chemistry lab equipments; state the joint size you use on the contact page.
Related Products
- Receiver Adapter, Plain Bend: The standard plain bend for open receivers placed close under the condenser.
- Receiver Adapters, Plain Bend, Short: The short plain bend for compact sets where height under the condenser is limited.
- Distillation Apparatus, Ammonia: An ammonia distillation apparatus, where a long delivery reaches into the trapping acid.
- Kjeldahl Distillation Assembly: A Kjeldahl distillation assembly that delivers released ammonia into boric or standard acid.
Frequently Asked Questions
How does the long plain bend differ from the standard plain bend?
Both are curved fittings with no side tube, but the long pattern has an extended delivery limb. The extra length carries distillate further down into the receiver, past the neck of a narrow flask, into a cooled receiver or towards the surface of an absorbing solution.
Can the tip of a long receiver bend dip under the receiving liquid?
It can, for example when ammonia is trapped in acid, but a dipped tip can suck liquid back into the condenser when heating drops. Keep the tip just clear of the surface where possible, and if it must dip, lower the receiver away before reducing or stopping the heat.
Why deliver volatile distillates low in the receiver?
Releasing the drops deep inside a cooled flask means less vapour escapes from the neck, so less of a low-boiling product is lost. Standing the receiver in an ice bath and delivering near the bottom works together to keep the collected volume close to what distilled.
Will a long receiver bend fit a short receiver?
Only if the receiver can be set low enough. The long limb may touch the bottom of a short flask, which blocks the flow and can trap the tip in liquid. Lower the receiver on a support or use the standard or short bend for short receivers.
Does the long plain bend vent the distillation set?
It has no side tube of its own; the set vents through the open mouth of the receiver around the delivery limb. Keep that gap open and never seal the long limb into a jointed receiver while heating.
How should a long bend be cleaned after an ammonia distillation?
Before removing it from the receiver, rinse the inside and outside of the tip into the receiving flask with distilled water, so no trapped ammonia is lost from the titration. Then wash the adapter with water and detergent, and rinse with distilled water.
Last Updated: November 2026










Reviews
There are no reviews yet.