Quick Answer: A PTFE key burette is a graduated glass burette whose stopcock plug is made of PTFE instead of glass. PTFE needs no grease and does not seize, so the burette suits alkaline titrants and routine titrations without stopcock maintenance.
Why a PTFE Plug Replaces Glass
The stopcock is the part of a burette that gives the most trouble. A glass key must be greased to turn smoothly and seal, the grease can creep into the bore and tip, and alkali solutions can cement a glass key in its barrel. A PTFE key burette avoids these problems because PTFE (polytetrafluoroethylene) is slippery, resists almost all laboratory reagents and does not bond to glass, so the key turns freely without lubricant.
The key is usually held in the glass barrel by a threaded nut and washer on its narrow end. Tightening the nut presses the tapered plug into the barrel to stop leaks; loosening it lets the key turn more easily and allows it to be removed for cleaning. PTFE is softer than glass and can slowly cold-flow, so the tension may need a small adjustment from time to time.
This makes the PTFE key burette the practical choice for sodium hydroxide titrant, for student benches where grease tends to be over-applied, and for titrations in which grease would contaminate the delivered liquid.
Care & Handling
- Do not overtighten the retaining nut; a key clamped too hard is stiff to turn and can crack the barrel.
- Remove the key before drying the burette in an oven, because PTFE and glass expand differently and the key may loosen or distort.
- Wash the key and barrel separately and check the bore for particles that would block delivery.
- Store burettes vertically in a burette stand or flat in a padded drawer, never leaning where they can roll.
Applications
- Acid-base titrations with sodium hydroxide titrant, which would seize a glass key
- Student titration practicals where no stopcock grease is wanted
- Non-aqueous titrations in organic solvents, which dissolve stopcock grease
- Redox titrations with potassium permanganate or iodine, which rule out rubber-tube burettes
Specifications
| Item | Graduated burette with PTFE stopcock key |
| Key material | PTFE (polytetrafluoroethylene), used without grease |
| Key retention | Nut and washer on the key end, as usual for this design |
| Suited titrants | Acids, alkalis, and most aqueous and non-aqueous reagents |
Why Choose LabEquip
College chemistry departments, pharmacy laboratories and schools replacing seized glass-key burettes often switch to PTFE keys. LabEquip lists this burette alongside the straight bore glass key burette in its chemistry lab equipment range; send sizes and quantities through the contact page.
Related Products
- Burette, Straight Bore Glass Key: A straight bore glass key burette, the classic greased-stopcock alternative.
- Burette, Rotaflow: A Rotaflow burette whose screw valve gives finer control near the end point.
- Burette Holder Clamp: A burette holder clamp to keep the burette vertical during titration.
- Brush, Burette: A burette brush with a long stem for cleaning inside the bore.
Frequently Asked Questions
Why choose a burette with a PTFE key?
A PTFE stopcock key needs no grease and does not seize in its barrel. It suits alkaline titrants, which can cement a glass key, and saves the time spent cleaning and regreasing stopcocks.
Do PTFE stopcocks on burettes need grease?
No. PTFE is naturally slippery and seals against the glass without lubricant. Adding grease only collects dirt and can contaminate the titrant, so keep the key and barrel clean and dry instead.
What holds a PTFE key in place on a burette?
A nut and washer on the end of the key, as is usual for this design, keep it seated in the barrel. Tighten the nut just enough to stop leaks while the key still turns smoothly; overtightening makes it stiff.
Which titrations suit a PTFE key burette?
It handles acids, alkalis and most aqueous and non-aqueous reagents. It is a sound everyday choice for acid-base titrations in schools and colleges, especially where sodium hydroxide is used regularly.
Why does a PTFE stopcock sometimes leak?
The nut may have loosened, or the key may be scratched or deformed. Retighten the nut gently and check the key for damage. Store the burette with the nut slightly loosened so the PTFE does not take a permanent set in the barrel.
How should you prepare a PTFE key burette before a titration?
Rinse it with distilled water, then twice with small portions of the titrant, draining through the tip each time. Fill above zero, run liquid through to clear air from the tip, and record the starting reading at eye level.
Last Updated: November 2026










Reviews
There are no reviews yet.