Search

In Stock

Capillary Tube

Uniform Internal Bore Diameter: Ensures consistent capillary action and reliable experimental results.

Borosilicate Glass Construction: Provides high resistance to heat, chemicals, and thermal shock during laboratory use.

₹210.00

Quick Answer: This Capillary Tube is a fine-bore glass capillary tube used in the physics laboratory to show capillary rise and to measure the surface tension of water by the capillary rise method. The same narrow glass tube, sealed at one end, is also the usual sample holder for melting-point determination.

Why Water Climbs a Narrow Glass Bore

Dip a clean, narrow glass tube vertically into water and the liquid inside rises well above the level outside. Water wets glass, so its surface curves into a concave meniscus, and the surface tension acting around the circle where water meets glass pulls the column upward. The column stops climbing when the weight of the raised water balances that upward pull. A narrower bore gives a higher column: halve the radius and the rise roughly doubles, which is why a fine bore is needed for a reading that can be measured.

The practical formula follows directly from that balance. Surface tension T equals r h ρ g divided by 2 cos θ, where r is the bore radius, h the height of the meniscus above the outside surface, ρ the density of water and θ the angle of contact. For water on clean glass the contact angle is taken as nearly zero, so T is close to r h ρ g / 2.

In the standard set-up the tube is clamped vertically with a pointer whose tip just touches the water surface. A travelling microscope is focused first on the bottom of the meniscus and then, after the beaker is removed, on the pointer tip, and the difference gives h. The same microscope then reads the bore across two perpendicular diameters at the cut end to give r.

Specifications

Item Capillary tube, glass
Bore Fine bore; the radius is measured as part of the experiment
Main practical Surface tension of water by the capillary rise method
Used with Clamp or capillary tube apparatus, travelling microscope, beaker of water
Bore, length and quantity per order Confirm at enquiry

Where the Capillary Tube Is Used

  • Finding the surface tension of water from the height of capillary rise
  • Showing that the rise increases as the bore becomes narrower, with tubes of different bores side by side
  • Comparing the rise in pure water and in soapy water to show how detergent lowers surface tension
  • Explaining why blotting paper, lamp wicks and soil draw water upward
  • Holding small powdered samples for melting-point determination after one end is sealed

Care & Handling

  • Clean the bore with warm detergent solution and rinse it with distilled water before measuring; any grease lowers the rise.
  • Clamp the tube vertically instead of holding it, so the meniscus stays steady while it is sighted.
  • Handle the tube by its ends and store it in a closed container; fine glass snaps easily and the broken ends are sharp.
  • Put broken capillaries in a glass-waste container, never in general waste.

Why Choose LabEquip

Physics departments order capillary tubes in quantity, because they break in student hands and because a surface-tension practical works better with a choice of bores. LabEquip supplies them alongside the capillary tube apparatus and the rest of its physics lab equipment, and bulk quantities for a practical batch can be arranged through the contact page.

Frequently Asked Questions

Why does water rise in a capillary tube while mercury falls?

Water wets clean glass and forms a concave meniscus, so surface tension pulls the column up the bore. Mercury does not wet glass; its meniscus is convex and surface tension pushes its level below the outside surface instead.

How is the radius of the bore measured?

The tube is laid horizontally and its cut end is viewed through a travelling microscope. The cross-wire is set on opposite edges of the bore along two diameters at right angles, and half the mean diameter is the radius used in the formula.

Why must the tube be so clean?

Grease or dust on the inner wall increases the angle of contact between water and glass. That lowers the column and makes the calculated surface tension too small, and even a fingerprint inside the bore can spoil a reading.

Why is the tube lowered and raised again before reading?

Pushing the tube further into the water and then lifting it back wets the bore above the final level. The meniscus then settles on a wet surface, which gives a steadier and more repeatable height than a column climbing over dry glass.

Can the same tube be used for a melting-point test?

Yes. One end is sealed by turning it in the edge of a flame, a little dry powder is tapped down to the closed end, and the tube is fixed beside a thermometer bulb in a heating bath. Keep tubes used for samples out of surface-tension work afterwards.

Does water temperature change the capillary rise?

Yes. The surface tension of water falls as it warms, so the column stands slightly lower in warm water. Record the water temperature with each reading so the result can be compared with the value for that temperature.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)