Quick Answer: The Torsion Apparatus/Barton’s Apparatus (Vertical Pattern) measures the modulus of rigidity of a rod by the static method, with the rod hanging vertically from a fixed clamp. In Barton’s apparatus a drum at the lower end is turned by two cords that pass over pulleys to equal weights, applying a pure couple, while pointers read the twist on circular scales.
Why Barton’s Pattern Uses Two Pulleys
When a single cord pulls on a drum, it applies a couple but also a sideways force, which the bearing has to resist, and some of the effort is lost to bearing friction. Barton’s arrangement avoids this. Two cords are wound around the drum and led away on opposite sides over two pulleys, each carrying an equal mass M. The two tangential forces are equal and opposite, so their resultant is zero and they form a pure couple: Mg multiplied by the drum diameter D.
With the rod vertical, the drum hangs on the rod itself, and nothing pushes the specimen sideways. Two pointers fixed to the rod a distance l apart move over horizontal circular scales, and the difference between their readings gives the twist θ over that length. The modulus of rigidity follows from η = 2MgDl/(πr⁴θ), with r the radius of the rod and θ in radians.
As in every static method, loads are increased in equal steps and then reduced, and θ is plotted against M. Equal masses on the two cords are essential: any difference leaves a net sideways pull, and part of the twist then depends on bearing friction rather than on the couple alone.
Specifications
| Pattern | Vertical: specimen rod hangs from a fixed upper clamp |
| Loading | Two cords over two pulleys with equal masses, forming a pure couple MgD |
| Readings | Two pointers on circular scales a measured distance l apart |
| Result | η = 2MgDl/(πr⁴θ) |
| Rods, pulleys and weight sets supplied | Confirm at enquiry |
Care & Handling
- Load both hangers of Barton’s apparatus equally and at the same time, so the rod is never pulled by one side alone.
- Check that the pulleys line up with the drum and turn freely; a cord rubbing on a pulley flange wastes part of the couple.
- Keep the rod hanging freely and vertical, with nothing touching the drum or the pointers.
- Unload completely after the practical and slacken the cords, so the rod is not left under strain.
Applications
- Determining the modulus of rigidity of a rod by the static method with a pure couple
- Plotting angle of twist against couple to confirm the linear elastic relation
- Comparing static results with Searle’s type apparatus or a torsion pendulum on the same material
- Demonstrating the difference between a couple and a single force in rotation lessons
Why Choose LabEquip
Barton’s apparatus is chosen by college laboratories that want a static rigidity experiment free from side loads on the specimen. The horizontal Searle’s type torsion apparatus uses a single cord and makes a useful comparison. Both appear in LabEquip’s physics lab equipment; use the contact page to ask about specimens and weights.
Frequently Asked Questions
What is a pure couple?
A pair of equal, parallel forces acting in opposite directions along different lines. It produces turning only, with no resultant force, so the bearing carries no side load. Here the two cords supply the two forces.
How is the couple calculated with two cords?
Each cord carries a weight Mg and pulls at the rim of the drum on opposite sides, so the couple is Mg multiplied by the drum diameter. Measure the diameter with vernier calipers and add one cord thickness.
Why must the two masses be equal?
Unequal masses leave a net sideways force on the drum. The rod and bearing then take part of the load, friction rises, and the twist no longer depends only on the couple.
Why read two pointers rather than the drum position?
A reading taken at the drum includes any slip at the upper clamp or in the fittings. The difference between two pointers fixed on the rod records only the twist of the length between them.
Does the vertical pattern give a different result from the horizontal one?
Both should give the same modulus of rigidity for the same specimen, because the physics is identical. The vertical pattern removes side loading by using a pure couple, so it often shows less scatter from bearing friction.
What materials can be tested?
Rods of common metals such as steel, brass, copper or aluminium are usual, as long as they fit the clamps. Softer metals twist more under the same couple, so smaller loads are used to stay within the elastic limit.
Last Updated: October 2026










Reviews
There are no reviews yet.