Search

In Stock

Inclined Plane, Brass

Precision Graduated Arc: Features a high-visibility protractor scale with a locking vertical adjustment mechanism, allowing for sub-degree precision when determining the angle of repose and resultant force components across various inclinations.

Low-Friction Brass Surface: Constructed from a heavy-gauge, high-polish brass board paired with a precision-aligned frictionless pulley, ensuring uniform surface-to-surface interaction for consistent, repeatable friction coefficient measurements during intensive laboratory cycles.

₹450.00

Quick Answer: A brass inclined plane is an adjustable slope, made with brass as its title indicates, on which a roller is held in equilibrium by a load hanging over a pulley. It is used to find the force needed to support a body on a slope and to show how that force varies with the angle of inclination.

Resolving the Weight of the Roller

A roller resting on a slope is acted on by three forces: its weight, straight down; the normal reaction of the plane, at right angles to the surface; and the pull of the thread, running parallel to the plane and over the pulley to the scale pan. In equilibrium, these three forces balance. Resolving the weight into components shows that the part acting down the slope is the weight multiplied by the sine of the angle, and the part pressing into the plane is the weight multiplied by its cosine.

A roller is used rather than a sliding block because rolling friction is small. With friction nearly removed, the load in the pan that holds the roller still is very close to the component of weight down the slope, so the experiment checks the resolution of forces directly.

Brass suits this apparatus: it is dense, so working parts of modest size carry a useful weight, and it resists tarnish and rust in a humid laboratory. Which parts are brass in the supplied version should be confirmed at enquiry.

Specifications

Type Adjustable inclined plane with roller, pulley and scale pan
Material Brass, as named
Angle Set by raising the plane and read on its scale
Effort Thread over the pulley to a scale pan, parallel to the plane
Brass parts, roller and pan supplied Confirm at enquiry

The Graph Method

Set the plane to an angle, read it on the scale, and add sand or small weights to the pan until the roller stays at rest anywhere on the plane. Record the total pulling force, including the pan, then repeat at several angles. Plotting the pulling force against the sine of the angle gives a straight line through the origin whose slope equals the weight of the roller, a result students can compare with its weight measured on a balance.

Applications

  • Finding the force on a roller acting down a slope and its relation to the sine of the angle
  • Resolving a weight into components parallel and perpendicular to a surface
  • Verifying the conditions for equilibrium of three forces
  • Discussing ramps, sloping roads and conveyor belts

Care & Handling

  • Keep the pulley bearing clean and lightly lubricated so it turns freely.
  • Wipe the plane and roller so dust does not add friction.
  • Polish brass parts with a soft dry cloth to remove fingerprints; avoid abrasive cleaners on the scale.
  • Check that the thread runs parallel to the plane before each reading.

Why Choose LabEquip

Senior-school physics laboratories buy the brass inclined plane for the practical on forces acting on a roller at different angles. LabEquip includes it in its physics lab equipment, with the deluxe inclined plane available for friction studies, and the parts supplied can be confirmed through our contact page.

Frequently Asked Questions

Why does the pulling force depend on the sine of the angle?

Only the component of the roller’s weight along the slope must be balanced. That component equals the weight multiplied by the sine of the angle of inclination.

Why is a roller used instead of a block?

Rolling friction is much smaller than sliding friction. With a roller, the balancing force is very close to the component of weight down the slope, which is what the experiment sets out to measure.

What does the slope of the force against sine graph represent?

It equals the weight of the roller. Comparing it with the roller’s weight measured on a balance checks the experiment.

Should the weight of the scale pan be included?

Yes. The pan itself pulls on the thread, so its weight must be added to the weights placed in it to give the total pulling force.

What is the normal reaction on the roller?

It is the push of the plane on the roller, at right angles to the surface, and equals the weight multiplied by the cosine of the angle when the pull is parallel to the plane.

Why must the thread be parallel to the plane?

The theory assumes the pull acts along the slope. If the thread slopes upwards or downwards, part of the pull acts into or away from the plane and the readings no longer match.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)