Search

In Stock

Resistance Substitution Box

Wide-Range Coverage: Utilizes multi-decade slide switches to deliver resistance from 1 ohm to 11.111 megohms, ensuring comprehensive compatibility with various low-power electronic circuits and experimental setups.

High-Accuracy Components: Incorporates 1-watt metal film resistors with a ±1% tolerance and minimal residual resistance, housed in a durable, shock-resistant case featuring high-conductivity binding posts for secure connections.

₹850.00

Quick Answer: The Resistance Substitution Box is a box of fixed resistors in standard preferred values, any one of which can be connected into a circuit in place of a component resistor. A resistance substitution box is used in electronics practicals and fault-finding to try different values quickly without soldering.

Trying Values Without Soldering

When a circuit is being designed or repaired, the right value for a resistor is often found by trial: a transistor’s bias, an LED’s current or an amplifier’s gain may need adjusting. The substitution box holds a set of fixed resistors, and a selector or set of terminals connects one of them at a time to the output leads. The leads are clipped into the circuit where the resistor would go, and the effect of each value is seen immediately.

Unlike a decade box, which builds almost any value digit by digit, a substitution box offers a fixed list of values, normally drawn from the preferred-number series used for commercial resistors. That is a practical advantage: once a value works, an ordinary resistor of the same value can be soldered in. The decade resistance box is the better choice where an exact, arbitrary resistance is wanted.

The values supplied, the number of positions and whether selection is by rotary switch or by terminals are not stated in the listing title and should be confirmed.

Uses

  • Choosing the current-limiting resistor for an LED
  • Setting the bias resistor of a transistor amplifier in senior electronics practicals
  • Fault-finding by substituting a known value for a suspect resistor
  • Teaching preferred values, tolerance and the resistor colour code

Care & Handling

  • Work out the power, current squared times resistance, before connecting; the resistors inside are small.
  • Switch the circuit off before changing the selected value.
  • Keep test leads short and tidy to avoid accidental shorts.
  • Store the box dry and away from heat.

Specifications

Type Resistance substitution box
Values Fixed resistors in standard preferred values
Selection One value at a time connected to the output
Use Trial substitution in low-power electronic circuits
Values, number of positions and selection method Confirm at enquiry

Why Choose LabEquip

Electronics teachers and technical institutes buy substitution boxes so that students spend practical time testing ideas rather than soldering and desoldering. LabEquip lists this box in Physics Equipments; confirm the values supplied through the contact page.

Frequently Asked Questions

What is the difference between a substitution box and a decade resistance box?

A substitution box offers a fixed set of standard resistor values, one at a time. A decade box can be set to almost any value in its range, digit by digit. Substitution boxes are quicker for trial and error with real components.

What are preferred values?

Resistors are made in standard series of values spaced so that, allowing for tolerance, the whole range is covered without gaps. Choosing from these values means that a successful trial can be replaced by an ordinary resistor.

How is the box used in fault-finding?

If a resistor in a circuit is suspected of having drifted or failed, lift one end of it and connect the box in its place, set to the marked value. If the circuit then works, the original resistor was at fault.

Can the box carry large currents?

No. The resistors inside are small electronic components with limited power ratings. Use it in low-power circuits and calculate the power, current squared times resistance, before connecting it.

Is it useful in school physics?

Yes, in senior electronics practicals such as setting the current through an LED or finding the bias resistor for a transistor amplifier. It also helps students learn resistor values and tolerance.

Why switch the circuit off before changing values?

Switching while powered can momentarily leave the circuit open or apply the wrong resistance, which may damage transistors or LEDs. Changing values with the power off avoids these surges.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)