Search

In Stock

Resistance Box Plug Type (Constantan / Manganin Coil)

Low Temperature Coefficient Alloys: Features non-inductively wound coils made from premium Constantan or Manganin, ensuring resistance remains stable despite thermal fluctuations during operation.

Precision Machined Contact Blocks: Equipped with heavy-duty tapered brass blocks and interchangeable plugs that provide negligible contact resistance for repeatable, high-resolution electrical output across all ranges.

₹1,470.00

Quick Answer: The Resistance Box Plug Type (Constantan / Manganin Coil) is a box of fixed resistance coils mounted under a row of brass blocks; pulling a brass plug out of the gap between two blocks brings that coil into the circuit. This plug type resistance box supplies known resistances for metre bridge, potentiometer and Ohm’s law practicals.

How the Plugs Add Resistance

On top of the box sits a row of thick brass blocks separated by narrow gaps. Beneath each gap a coil of resistance wire is connected between the neighbouring blocks. With a tapered brass plug pushed into the gap, current takes the low-resistance path through the plug and the coil is short-circuited. Pulling the plug out forces the current through the coil, so the resistance in circuit is the sum of the values marked beside the open gaps.

Constantan and manganin are used for the coils because both alloys combine high resistivity with a low temperature coefficient, so the values hold steady as current flows. Manganin is the more stable over time and is preferred for standard resistors; constantan is widely used in teaching instruments. Coils in such boxes are often wound non-inductively, doubled back on themselves, so that the box acts as a pure resistance.

The title names both alloys; which alloy and which coil values are supplied should be confirmed when ordering. The plug type is the box most often used as the known arm of a meter bridge, while the decade resistance box sets values with selectors when they must be changed frequently.

Applications

  • Known resistance R in metre bridge and post office box experiments
  • High series resistance for converting a galvanometer into a voltmeter
  • Shunt resistance for converting a galvanometer into an ammeter
  • Finding the figure of merit of a galvanometer
  • Supplying known resistances in Ohm’s law and internal resistance practicals

Specifications

Type Plug type resistance box
Coils Constantan or manganin resistance wire (as titled)
Selection Brass plugs removed to add coils
Value in circuit Sum of the coils whose plugs are out
Coil values and total resistance Confirm at enquiry

Care & Handling

  • Seat each plug with a slight twist; a loose plug adds contact resistance.
  • Keep plugs clean and avoid touching their tapered surfaces with greasy fingers.
  • Store the box with all plugs in place so none are lost and the sockets stay clean.
  • Keep currents small and brief, and use a key so they flow only while readings are taken.

Why Choose LabEquip

Physics teachers buy plug type resistance boxes in numbers because nearly every bench-level electricity practical needs one as a known resistance. LabEquip lists this box in its Physics Equipments range; send coil value and alloy requirements through the contact page.

Frequently Asked Questions

How do I read the resistance from a plug type resistance box?

Add up the values marked beside every gap whose plug has been removed. Plugs left in place contribute almost nothing, because current flows through the brass plug instead of the coil.

Why do loose plugs cause errors?

A plug that is not fully seated makes poor contact with the blocks and adds an unknown resistance. Press each plug in with a slight twist and check that all unused plugs are tight before taking readings.

What is the difference between constantan and manganin coils?

Both are copper-based alloys with high resistivity and low temperature coefficients. Manganin is the more stable against temperature and over time, which is why it is used in standard resistors; constantan is also common in teaching instruments and in thermocouples.

Can the box convert a galvanometer into a voltmeter?

Yes. A high resistance taken from the box and placed in series with the galvanometer turns it into a voltmeter. The value required is calculated from the galvanometer resistance, its full-scale current and the voltage range wanted.

Why keep all the plugs in when the box is stored?

It protects the brass sockets from dust and corrosion, stops plugs from going missing and leaves the box at zero, so no student unknowingly puts the whole resistance into the next circuit.

How much current can the coils carry?

Resistance boxes are made for measurement, not for controlling large currents. Keep currents small and use a key so they flow only during readings. A rheostat is the right tool for heavier currents.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)