Search

In Stock

Meter Bridge or Wheatstone Bridge With Pencil Jockey

Industrial-Grade Construction: Features heavy-duty, polished brass blocks and thick strips mounted securely on a seasoned teak-wood base for maximum conductivity and structural stability.

Precision Measurement Wire: Equipped with a 24-SWG Constantan resistance wire stretched across an inlaid 100cm meter scale with clear millimeter graduations for exact null-point detection.

₹1,020.00

Quick Answer: The Meter Bridge or Wheatstone Bridge With Pencil Jockey is a Wheatstone bridge in which two of the four arms are formed by a uniform resistance wire one metre long, as the name indicates, stretched beside a scale. Sliding the pencil jockey to the point of zero galvanometer deflection gives an unknown resistance from the ratio of the two wire lengths.

The Balance Condition

A Wheatstone bridge has four resistances in a loop, with a galvanometer joining two opposite corners. When the bridge balances, no current flows through the galvanometer and the ratio of resistances on one side equals the ratio on the other. In the metre bridge the known resistance R, taken from a resistance box, and the unknown S sit in two gaps of a thick metal strip, and the other two arms are the lengths of wire on either side of the jockey. At balance S = R(100 – l)/l, with l in centimetres measured from the end next to R.

The pencil jockey is the contact that touches the wire. It should be pressed lightly and briefly at each trial point, never dragged along, because scraping the wire changes its cross-section. The balance point is found by narrowing in between two positions that give opposite galvanometer deflections.

Accuracy is greatest when the balance point lies near the middle of the wire, so choose R from the plug type resistance box to bring it there. Interchanging R and S and averaging the two results cancels the end errors caused by contact resistance where the wire meets the strips. The post office box applies the same principle in compact form.

Specifications

Type Metre bridge (slide-wire Wheatstone bridge)
Bridge wire Uniform resistance wire one metre long, beside a metre scale
Gaps Two gaps in a metal strip for the known and unknown resistances
Contact Pencil jockey
Used with Resistance box, galvanometer, cell, key and connecting leads
Wire alloy and base material Confirm at enquiry

Applications

  • Finding an unknown resistance by the balance-point method
  • Determining the resistivity of a wire material, with its diameter from a screw gauge
  • Verifying the laws of resistances in series and in parallel
  • Comparing two resistances

Care & Handling

  • Press the jockey down gently and lift it before moving; never slide it along the wire.
  • Close the cell key only while taking a reading so the wire does not warm up.
  • Keep terminal screws tight and the strips clean, since dirty contacts add resistance.
  • Store the bridge flat with nothing resting on the wire.

Why Choose LabEquip

School and college physics laboratories keep several metre bridges because the experiment appears in practical examinations year after year. LabEquip lists this bridge with its other physics lab equipment, and our contact page handles orders for full bench sets.

Frequently Asked Questions

What is the formula for an unknown resistance on a meter bridge?

With the known resistance R in the left gap, the unknown S in the right gap and the balance point l centimetres from the left end, S = R(100 – l)/l. The two lengths of wire act as the ratio arms of the bridge.

Why should the balance point be near the middle of the wire?

Near the centre, a small error in reading l causes the smallest percentage error in the calculated resistance. Choose a known resistance close to the expected unknown value to bring the balance point there.

What are end errors and how are they removed?

The ends of the wire join the metal strips, and contact resistance there adds small unknown lengths to the wire. Interchanging the known and unknown resistances and averaging the two results largely cancels the error.

How do I find the resistivity of a wire?

Find the resistance of a measured length of the wire on the bridge, then measure its diameter at several points with a screw gauge. Resistivity equals resistance multiplied by cross-sectional area, divided by length.

Why should the jockey not be slid along the wire?

Dragging the jockey scratches and thins the wire, so it is no longer uniform and the length ratio no longer equals the resistance ratio. Press it down briefly at each point and lift it before moving.

Why is a key used in the cell circuit?

Current warms the wire and changes its resistance. Closing the key only while a reading is taken keeps the wire cool, keeps the balance point steady and saves the cell.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)