Search

In Stock

Joule Effect Model

Maquette effet Joule Cuve transparente pour visualiser la résistance et l'élévation de température, features a precision-wound resistive heating coil housed in a protective sheath, engineered to maintain consistent resistance values during high-current thermal cycles.

Universal Safety Interface Couvercle avec agitateur et passage pour thermomètre, Equipped with standardized 4mm shrouded safety sockets, enabling seamless integration with regulated laboratory power supplies for accurate current (I) and voltage (V) modulation.

₹2,340.00

Quick Answer: The Joule effect model is an apparatus that shows how an electric current heating a resistor in a liquid turns electrical energy into heat. Students use the Joule effect model to test how the heat produced depends on current, resistance and time, and to find the specific heat capacity of water electrically.

Joule’s Law of Heating

When a current flows through a resistor, collisions between the moving electrons and the vibrating ions of the conductor transfer energy to the material, which warms up. The energy converted is E = VIt, and since V = IR this is also E = I²Rt. The square of the current is the key feature: doubling the current quadruples the rate of heating, which is why cable ratings and fuses matter so much.

In the model, the resistor sits in a known mass of water inside an insulated vessel, so almost all the electrical energy ends up raising the water’s temperature. Comparing the electrical energy supplied with the heat gained by the water is a direct test of energy conservation.

Investigations to Run

Holding the resistance and time fixed and repeating at several currents gives temperature rises that grow with I²; a graph of temperature rise against I² is a straight line through the origin, while a graph against I is a curve. Changing only the time at a fixed current shows a rise proportional to time, as long as the temperature stays close to room temperature so that heat losses remain small.

For the specific heat capacity of water, record voltage, current and time, weigh the water and measure the temperature rise. Then c = VIt / (mΔθ), with a correction for the vessel’s heat capacity. Starting slightly below room temperature and finishing a similar amount above it helps balance the heat gained and lost during the run.

Investigations Supported

  • Showing that heating depends on the square of the current
  • Finding the specific heat capacity of water by electrical heating
  • Testing energy conservation between electrical input and heat gained
  • Linking Joule heating to fuses, cable ratings and heating elements

Specifications

Product Joule effect apparatus (electrical heating model)
Principle Conversion of electrical energy to heat, E = VIt = I²Rt
Measurements Voltage, current, time, water mass and temperature rise
Typical results Heat proportional to I², R and t; specific heat capacity of water
Vessel, resistor and supply requirements Confirm at enquiry

Care & Handling

  • Switch on the supply only when the resistor is fully submerged; a resistor heated in air can overheat
  • Stir gently and continuously during heating so the thermometer reads the average water temperature
  • Keep connections dry and away from spilled water
  • Allow the apparatus to cool and empty it after use

Why Choose LabEquip

Among electricity experiment kits for schools, the Joule effect model is the one that links circuits to energy and heat in a single practical. It works with an autonomous direct current joulemeter for measuring energy directly, and with submersible resistors for comparing resistance values; contact LabEquip for details.

Frequently Asked Questions

Why does doubling the current produce four times the heat?

The heating power is I²R, so it depends on the square of the current. Twice the current through the same resistor gives four times the power and four times the heat in the same time.

How is the specific heat capacity of water found with the model?

Measure the voltage, current and heating time to find the electrical energy, and the mass and temperature rise of the water. Dividing the energy by mass times temperature rise gives c, with a correction for the vessel.

Why should the resistor be fully under water before switching on?

In air the resistor cannot shed heat quickly and may overheat or damage its connections. In water the heat is carried away and can be measured.

Why does the measured value of c often come out too high?

Some of the electrical energy is lost to the surroundings and to the vessel, so the water warms less than expected. The calculation then credits the water with more energy per degree than it actually needed.

What graph shows Joule’s law most clearly?

Temperature rise against the square of the current, for fixed time and resistance. It gives a straight line through the origin, while plotting against current alone gives a curve.

What precautions does the experiment need?

Use the power supply intended for the apparatus, keep connections and hands dry, switch off before handling the resistor, and let it cool before emptying the vessel.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)