Search

In Stock

Electronic Repair Suitcase

Valise réparation électronique, ESD-Safe Instrumentation Facilitates the safe manipulation of sensitive CMOS components in static-controlled environments, reinforcing Bloom’s "Apply" level of technical proficiency.

Integrated Suction and Non-Marring Prying Tools support the "Analyze" cognitive phase by allowing non-destructive disassembly for internal hardware diagnostic assessments and forensic failure analysis.

₹3,250.00

Quick Answer: The electronic repair case is a carry case of tools for diagnosing and repairing electronic circuits, robots and models in a school workshop. A case of this kind typically groups a multimeter for fault-finding, soldering and desoldering tools, and small hand tools in one place.

Fault-Finding with a Multimeter

Most electronic repairs start with measurement. With the circuit powered, a multimeter on its voltage range checks that the supply reaches each part of the board and that the voltages across components match what the circuit diagram expects. With the power off, its resistance or continuity range finds broken tracks, dry joints and failed switches, and its diode test checks LEDs and diodes in both directions.

Working methodically matters more than the tools. Students learn to start at the power supply and follow the signal, compare a faulty board with a working one, and change one thing at a time. Writing down each reading builds the habit of evidence-based repair and makes it easy for a teacher to see where reasoning went wrong.

Specifications

Item Carry case of tools for electronic repair
Typical contents Multimeter, soldering and desoldering tools, screwdrivers, pliers, cutters, tweezers
Use Diagnosing and repairing circuits, robots and models
Level Secondary and vocational technology courses
Exact contents and soldering iron rating Confirm at enquiry

Soldering and Desoldering

Replacing a component means removing the old one cleanly. Desoldering braid, laid on a joint and heated, soaks up the molten solder by capillary action so the leg can be lifted out without damaging the board. A new part is then fitted, the joint heated with the iron tip, and solder fed in until it flows into a smooth, shiny cone around the leg.

Safety rules are simple but important: return the iron to its stand every time, work in a ventilated area away from flux fumes, wash hands after handling solder, and switch the iron off at the end of the session. Which tools and which soldering iron this case contains should be confirmed before ordering.

Workshop Uses

  • Fault-finding practice on school robots and electronic models
  • Replacing components on damaged boards
  • Teaching multimeter technique for voltage, resistance and continuity
  • Maintaining classroom electronics kits

Care & Handling

  • Rest a hot soldering iron only in its stand, and let it cool before packing it away
  • Choose the right meter range, and disconnect power before resistance checks
  • Return each tool to its place so missing items are spotted quickly
  • Keep the case dry and away from heat sources

Why Choose LabEquip

Technology departments buy the case so that broken robots, models and kits can be repaired in class rather than thrown away. LabEquip also lists a smartphone repair kit and a dynamo lamp repair kit for repair-focused lessons, within its physics lab equipment range; confirm the contents via LabEquip contact.

Frequently Asked Questions

What is the first step in repairing a faulty circuit?

Check the power supply. Measure the voltage where it enters the board, then follow it through the circuit, comparing readings with what the diagram expects.

Why switch off before measuring resistance?

A resistance or continuity test sends a small current from the meter. Any voltage already present in the circuit gives false readings and can damage the meter.

What is a dry joint?

A dry joint is a solder joint that has not wetted the metal properly and often looks dull and grainy. It can make intermittent contact and is a common cause of faults.

How does desoldering braid work?

The braid is a fine copper mesh. Heated against a joint, it draws molten solder into itself by capillary action, freeing the component leg.

What safety rules apply to soldering in class?

Keep the iron in its stand when not in use, work with ventilation, avoid touching the hot tip or fresh joints, wash hands afterwards and switch off at the end.

Is the case suitable for students or only teachers?

With supervision and the safety rules above, secondary and vocational students can use it for structured repair activities.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)