Quick Answer: The Dielectric Constant Experimental Kit (Resonance Method) finds the relative permittivity of a material by placing it between the plates of a capacitor in a tuned LC circuit and measuring how the resonant frequency changes. This dielectric constant kit is used in undergraduate physics and electronics laboratories to measure the dielectric constant of insulating sheets.
How the Resonance Method Works
An inductor L and capacitor C connected together resonate at a frequency f = 1/(2π√(LC)). If the capacitor is a parallel-plate cell, its capacitance with air between the plates is C0 = ε0A/d. Filling the gap with a dielectric of relative permittivity εr raises the capacitance to εrC0, which lowers the resonant frequency. Because f is proportional to 1/√C, the ratio of the two capacitances, and hence εr, equals the square of the ratio of the resonant frequencies: εr = (f0/f)².
Resonance is located by driving the circuit from a variable-frequency oscillator and watching for the peak in voltage across the circuit, or the peak in current, on a meter or oscilloscope. In an alternative arrangement, the frequency is kept fixed and a calibrated variable capacitor is adjusted to restore resonance after the sample is inserted; the change in capacitance then gives the sample’s contribution directly.
Specifications
| Method | LC resonance with a parallel-plate sample capacitor |
| Quantity measured | Relative permittivity (dielectric constant) of a sample |
| Key relationship | εr = (f0/f)², from f = 1/(2π√(LC)) |
| Resonance detected with | Variable-frequency oscillator and a meter or oscilloscope |
| Components, sample set and frequency range | Confirm at enquiry |
Practical Points
The sample should fill the space between the plates completely and lie flat against them, since any air gap acts as a second capacitor in series and makes the measured permittivity too low. Stray capacitance from leads and the circuit board adds to C at both settings; it is reduced by keeping wiring short and, where the kit allows, by measuring the circuit’s own capacitance and subtracting it. Readings at more than one plate separation help separate the sample’s effect from these fixed strays.
Experiments
- Measuring the dielectric constant of insulating sheets such as glass, acrylic, Bakelite or mica
- Comparing the permittivity of different insulating materials
- Studying LC resonance and the effect of capacitance on resonant frequency
- Estimating stray capacitance in a tuned circuit
- Relating permittivity to the polarisation of molecules in a dielectric
Care & Handling
- Keep the capacitor plates clean, flat and parallel; scratches and dents change the gap.
- Handle dielectric samples by the edges and store them flat so they do not warp or pick up grease.
- Switch the oscillator off before rearranging the circuit, and use mains-powered instruments only with sound leads and proper earthing.
- Note the room temperature, since the permittivity of some materials changes with temperature and humidity.
Why Choose LabEquip
This kit is bought by colleges for the dielectric and AC circuit experiments in degree physics and electronics courses. It is listed in LabEquip’s Physics Equipments; for the basic parallel-plate idea, the Aepinus condenser is a useful classroom companion. Discuss sample materials through the contact page.
Frequently Asked Questions
Why does inserting a dielectric lower the resonant frequency?
The dielectric raises the capacitance of the plates. Since the resonant frequency of an LC circuit is inversely proportional to the square root of capacitance, a larger capacitance gives a lower frequency.
Why is the dielectric constant the square of the frequency ratio?
The frequency depends on one over the square root of capacitance. The capacitance ratio with and without the sample is therefore the square of the frequency ratio, and that capacitance ratio is the relative permittivity.
Why does an air gap make the result too low?
Any air left between the sample and the plates acts as a thin capacitor in series with the sample. The combined capacitance is smaller than that of the sample alone, so the calculated permittivity is underestimated.
How is resonance detected?
As the oscillator frequency is swept, the voltage across a parallel LC circuit rises to a sharp peak at resonance, or the current through a series circuit peaks. A meter or oscilloscope shows the peak, and the frequency at the maximum is recorded.
What dielectric materials can be tested?
Any flat, rigid insulating sheet that fits between the plates, such as glass, acrylic, Bakelite or mica. Conducting or damp materials are unsuitable, as they short the plates or add losses that broaden the resonance.
How does this method compare with measuring capacitance directly?
A capacitance meter can do the same job at a single frequency, but the resonance method teaches the physics of tuned circuits and can be extended to study how permittivity changes with frequency.
Last Updated: October 2026










Reviews
There are no reviews yet.