Quick Answer: Carbon Electrodes are graphite rods used in pairs as the anode and cathode of a simple electrolytic cell. Because carbon conducts but resists dissolving in most electrolytes, carbon electrodes let students see what the current itself does to a solution, from plating copper to releasing gases.
Building a Simple Electrolytic Cell
Two carbon rods are clamped upright in a beaker of electrolyte so that they do not touch, then connected through a switch and an ammeter to a low-voltage DC supply. The rod joined to the positive terminal becomes the anode and attracts negative ions; the rod on the negative terminal is the cathode and attracts positive ions. Clips or a holder keep the gap constant, which matters if students compare currents between different solutions.
With copper(II) sulfate solution, a pink layer of copper builds up on the cathode while oxygen bubbles form at the anode and the blue colour slowly fades. With concentrated sodium chloride solution, hydrogen appears at the cathode and chlorine at the anode, identified by its bleaching of damp litmus paper. Dilute sulfuric acid gives hydrogen and oxygen in roughly a two-to-one volume ratio when the gases are collected over each electrode.
Why Graphite Rather Than Metal
A copper or iron anode would itself dissolve into the solution and hide the reaction the lesson is about. Graphite is a form of carbon whose layered structure contains delocalised electrons, so it conducts well, yet it reacts with very few electrolytes at the low voltages used in schools. The one common exception is a carbon anode releasing oxygen at high current for a long time: the oxygen slowly attacks the carbon, forming carbon dioxide, and the rod erodes and sheds black particles.
Specifications
| Material | Carbon (graphite) rods |
| Role | Inert anode and cathode in electrolysis |
| Electrical behaviour | Good conductor; does not dissolve in most school electrolytes |
| Supply used with | Low-voltage DC from cells or a battery eliminator |
| Rod size and quantity per set | Confirm at enquiry |
Practicals
- Electrolysis of copper(II) sulfate, sodium chloride and dilute acid solutions
- Testing which liquids conduct, by placing the electrodes in tap water, sugar solution, salt solution and dilute acid with a bulb or ammeter in series
- Investigating how current changes with electrolyte concentration or electrode separation
- Weighing the cathode before and after copper plating to relate mass deposited to charge passed (Faraday’s first law)
- Building a simple cell with a zinc strip and a carbon rod in an electrolyte
Care & Handling
- Graphite is brittle: clamp the rods gently and do not use them to stir.
- Scrub off copper deposits with fine abrasive paper, or soak the rod in dilute nitric acid under a teacher’s supervision, then rinse well.
- Rinse carbon electrodes in water after every practical, because electrolyte left in the pores crystallises and contaminates the next experiment.
- Run chloride electrolysis only briefly and in a well-ventilated room, as chlorine is toxic.
Why Choose LabEquip
Teachers usually order carbon electrodes several pairs at a time, because each bench group sets up its own cell. They are listed in the LabEquip Physics Equipments category; for collecting and measuring the gases produced, see the Hoffman voltameter. Quantities and rod sizes can be confirmed through our contact page.
Frequently Asked Questions
Which electrode does copper collect on?
Copper always deposits on the cathode, the electrode connected to the negative terminal, because positive copper ions gain electrons there. If the copper appears on the wrong rod, the supply leads have been swapped.
Why does the anode crumble after long use?
When oxygen is released at a carbon anode, some of it reacts with the carbon to form carbon dioxide. Over many practicals this eats into the surface and loosens particles. Short run times and low currents slow the wear.
Can the electrodes be used with alternating current?
They will conduct AC, but each rod then switches between anode and cathode many times a second, so products form at both and the clear separation that electrolysis lessons rely on is lost. Use a DC supply.
How far apart should the electrodes be?
Far enough that they cannot touch or be bridged by bubbles, and kept at the same spacing for any comparison. A closer gap gives a larger current from the same supply voltage, because the path through the electrolyte is shorter.
Are these electrodes suitable for electroplating?
They work as the cathode for showing that a metal can be deposited, but for real plating the anode is normally made of the plating metal so that it dissolves and replaces the ions used up. A carbon anode lets the solution become steadily weaker in metal ions.
How do I deal with the black specks left in the beaker?
The specks are fine carbon shed from the anode. Let them settle, pour the solution into the waste container your school uses for electrolytes, and wipe the beaker with a damp paper towel before washing it normally.
Last Updated: October 2026










Reviews
There are no reviews yet.