Quick Answer: The Neodymium Block is a rectangular block magnet made of neodymium-iron-boron (NdFeB), usually with its poles on two opposite flat faces. A neodymium block magnet gives a very strong field over a flat area, which suits motor-effect experiments, eddy-current damping and other demonstrations needing a powerful, even field.
Why a Block Shape Helps
A block magnet presents a large flat pole face. Two blocks fixed to a steel yoke with opposite faces towards each other create a gap in which the field is both very strong and close to uniform, more so than between the poles of a horseshoe magnet. A small conductor placed in that gap feels a large force for a modest current, which makes the motor effect obvious even with a low-voltage supply.
Like all neodymium-iron-boron magnets, the block is usually plated against corrosion, is brittle despite its metallic look, and is weakened permanently by heat. Blocks are also heavy enough for their attraction to steel to trap fingers, so they should be handled one at a time and slid, not pulled, from steel surfaces.
Specifications
| Type | Rectangular block permanent magnet |
| Material | Neodymium-iron-boron (NdFeB), usually plated |
| Poles | Usually on two opposite flat faces |
| Main use | Strong, even field across a gap, for example on a steel yoke |
| Block dimensions, grade and coating | Confirm at enquiry |
Demonstrations and Investigations
- Showing the force on a current-carrying wire with a strong, even field
- Damping the swing of an aluminium pendulum plate with eddy currents
- Comparing the strength of neodymium, ferrite and Alnico magnets by lifting tests
- Showing magnetic forces acting through materials such as wood and glass
Eddy-Current Damping
A flat aluminium plate hung as a pendulum and swung between two neodymium blocks on a yoke stops almost dead as it enters the field. Eddy currents induced in the plate oppose its motion, converting its kinetic energy into heat. Repeating the swing with a plate cut into fingers by slots shows much less damping, because the slots break up the current paths.
The same principle is used in the magnetic brakes of trains and roller coasters and in the damping of sensitive balances and meters, so the demonstration connects directly to engineering. For a related effect in a tube, LabEquip also lists neodymium cylinders.
Care & Handling
- Handle one block at a time and keep other magnets and steel tools well away.
- Slide a block off a steel surface rather than pulling it straight up.
- Wear eye protection when blocks are being separated or assembled on a yoke.
- Keep away from pacemakers, bank cards, phones and computers, and from heat.
Why Choose LabEquip
Colleges and senior-school laboratories buy neodymium blocks for demonstrations that need a strong field over a flat area, such as eddy-current damping and the motor effect. LabEquip lists them with the other magnets in its physics equipment category, and block sizes for a particular yoke can be discussed through the contact page.
Frequently Asked Questions
What are neodymium block magnets used for in the laboratory?
Mainly for demonstrations that need a strong, even field over a flat area: the force on a current in a wire, eddy-current damping of a pendulum, and comparisons of magnet strength.
Where are the poles on a neodymium block?
Usually on two opposite flat faces, as the block is magnetised through one of its dimensions. Test each face with a compass and mark the north face before use.
Why does an aluminium plate stop swinging between two blocks?
The moving plate cuts through the strong field and eddy currents are induced in it. These currents interact with the field to produce a force opposing the motion, so the plate is braked quickly.
How should a neodymium block be separated from steel?
Slide it sideways to the edge of the steel surface rather than lifting it straight off. Sliding needs much less force and avoids sudden release that could trap fingers or chip the block.
Do neodymium blocks need a keeper?
No. The material resists demagnetisation strongly, so it needs no keeper. It should be kept away from heat, which can weaken it permanently.
What safety precautions are needed with neodymium blocks?
Prevent blocks from slamming together or onto steel, wear eye protection when assembling them, and keep them away from young children, pacemakers and electronic devices.
Last Updated: October 2026










Reviews
There are no reviews yet.